Compute the delay angle a required for a full-wave controlled rectifier to deliver an average outputcurrent of 12.5 A to a 7.5 Q load from a 120 Vrms ac source. A half-wave controlled rectifier is supplied by a 230 Vrms voltage source and has load resistance of2502. Calculate the delay angle a that produces a load-absorbed power of 200W.

Step 1: Given half wave controlled rectifier:and: Vin=230V,R=25Ω,P=200W,α=? Step 2: The rms output…

Answered: Compute the delay angle a required for…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
A 50 ohms load resistance is connected across a half wave rectifier. The input supply voltage is 230V (rms) at 50 Hz. Determine the DC output (average) voltage (4 significant figures) *
The rectifier below is operating at a frequency of 60 Hz, and the RMS value of the transformer output voltage v, is 6.3 V. (a) What is the value of the dc output voltage Vo (the peak V.) if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.50? (c) What is the required PIV rating of the diode in this circuit? (d) Sketch the output waveform labeling Vpeak (the dc value), Vripple, and sketch the general shape of the diode current Ip below the voltage waveform. + D1 R
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: a) Peak AC voltage Vm of the source b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance
A half-wave rectifier is needed to supply 15 VDC to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. a) What is the minimum value allowed for the smoothing capacitance? b) What if a full-wave rectifier is needed?
Please help me
A single-phase full bridge uncontrolled rectifier is supplied by 220 V (rms) line voltage. The load is pure resistive. What is the output Ripple Factor ?

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS