i need the answer quickly A GSM1800 cell tower antenna istransmitting 2OW of power in thefrequency range of 1840 to1845MHZ. The gain of the antenna is17dB. Find the power density at adistance of (a) 50m and (b) 300m inthe direction of maximum radiation.31.8 W/m2, 88*10^-5W/ m231.8 mW/m2, 0.88m W/ m231.8m W/m2, 0.88 W/ m2Option 431.8 W/m2, 88*10-3 W/ m2If PLF=0 dB means.. .Power is lost 100%Power is lost 0%O Power is lost 5

Given Two multiple choice question on array concept. Please find the below attachment for clear…

A GSM1800 cell tower antenna is transmitting 20W of power in the frequency range of 1840 to 1845MHZ. The gain of the antenna is 17dB. Find the power density at a distance of (a) 50m and (b) 30Om in the direction of maximum radiation. 31.8 W/m2, 88*10^-5W/ m2 31.8 mW/m2, 0.88m W/ m2 31.8m W/m2, 0.88 W/ m2 Option 431.8 W/m2, 88*10-3 W/ m2 If PLF=0 dB means. . Power is lost 100% Power is lost 0% Power is lost 5 K

A GSM1800 cell tower antenna is transmitting 20W of power in the frequency range of 1840 to 1845MHZ. The gain of the antenna is 17dB. Find the power density at a distance of (a) 50m and (b) 30Om in the direction of maximum radiation. 31.8 W/m2, 8810^-5W/ m2 31.8 mW/m2, 0.88m W/ m2 31.8m W/m2, 0.88 W/ m2 Option 431.8 W/m2, 8810-3 W/ m2 If PLF=0 dB means. . Power is lost 100% Power is lost 0% Power is lost 5 K

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question.
Complete solution otherwise skip. Plxxx.
i need the answer quickly
Question Completion Status: Click Submit to complete this assessment. Question 8 What do you do to an asynchronous counter to let it count froms14 to 0? (Handwriting solution is needed: include this in your pdf file) Click Submit to complete this asseESment,
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
When using an oscilloscope for testing engine management systems, what is an attenuator used for? In your answer provide an example of when an attenuator should be used. (5 - 10 words)
4. Do some search about the functionality of Airport Metal Detectors. Explain your answer in a paragraph.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.