A group of piles as shown on the figure has a cross section of 0.30 m x 0.30 m. It has a total length of 15 m. The piles are embedded in a homogeneous saturated clay with Cu = 70 kPa. Unit weight of clay is 18.8 kN/m³ and the ground water table is located at a depth of 18 m. below the ground surface. Factor of safety = 4. Compute the allowable load- bearing capacity of the group of pile acting as individual piles. Qll Clay Cu70 Pa .70 15m 56 m- L-2.74 m -Lz=3,96– Ans. 2816.10 kN

A group of piles as shown on the figure has a cross section of 0.30 m x 0.30 m. It has a total length of 15 m. The piles are embedded in a homogeneous saturated clay with Cu = 70 kPa. Unit weight of clay is 18.8 kN/m³ and the ground water table is located at a depth of 18 m. below the ground surface. Factor of safety = 4. Compute the allowable load- bearing capacity of the group of pile acting as individual piles. Qll Clay Cu70 Pa .70 15m 56 m- L-2.74 m -Lz=3,96– Ans. 2816.10 kN

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.36P: Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in...

See similar textbooks

Similar questions

A group of 9 friction piles, 10 m long is used as a foundation for a bridge pier. The piles used are 30 cm in diameter with centre to centre spacing of 0.9 m. The sub soil consists of clay with unconfined compressive strength of 1.5 kg/cm2. The efficiency for pile group will be (Take a = 0.9)
0.45m Square prestressed concrete piles are to be installed in groups of 4 at the site shown in the figure below. The center-to-center spacing between piles is 2.55 m. - Ground Level Soft Clay Su = 15kPa - Depth =6.7m Silty Clay Su = 30kPa 3m Depth = 15.1m 3m Medium Stiff Clay S,-80kPa - Depth = 20.0m a. Calculate group capacity based on individual failure b. Calculate group capacity based on block failure c. Based on parts (a) and (b) above determine the allowable downward load capacity for the pile group. Assume factor of safety of 2.5.
A group of piles are arranged as shown in the figure. The piles are square in section with sides equal to 400 mm and has a spacing of 1.80 m on centers. One pile has a total length of 18 m. Unit weight of clay is 19.7 kN/m3 and has a cohesion of 90 kPa. Ground water table is located at depth of 20 m below the ground surface. Adhesion factor is 0.90. Determine the ultimate load – bearing capacity of the group of piles considering the piles acting individually.
A group of 9 piles, 12 m long and 400 mm in diameter is arranged in a square pattern in homogeneous clay soil. The c/c spacing of the pile are 1000 mm. The properties of clay soil is given below Cc =0.10, e0=0.9, γsat = 20 kN/m^3, unconfined compressive strength qu= 70 kN/m^2 assume adhesion factor 0.7,. Water table is at GL. Determine the FOS against bearing if 1500 kN load is applied on the pile group and total settlement of pile group under the same load
A group of 9 piles of 33 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.32m. the length of the piles is 13 m. Unit cohesion of the clay is 70kPa. Determine the ultimate group capacity of the pile froup based on block failure. Assume adhesion factor of 0.75.
A nine-pile group composed of 0.30 m diameter pipe piles is embedded 15 m in clay soil with conditions indicated by the sketch. 1. Det the total capacity if piles act individually 2. Find the total capacity if piles act as a group 3. Det the design load if factor of safety is 3. C = 42.81 kpa a = 0.85 6m C = 57.46 kpa a = 0.75 6m C = 95.76 kpa a = 0.5 Nc = 8 3m 0.75m 1-8 0.75m 上tt 0.75m 0.75m
Problem 2 6m m 3m 0.75m 0.75m sharon 0.75m 0.75m C=42.81 kpe 0.85 C-57.40 kpa a=0.75 C-95.76 kpa a=0.5 No = 8 A nine-pile group composed of 0.30m diameter pipe piles is embedded 15m in clay soil with conditions indicated by the sketch. Determine the following: a. Capacity if piles acting individually b. Total capacity if piles act as a group c. Design load if factor of safety is 3.
The section of 4*5 group pipe pile, each 15 m in long, embedded in clay layer, the diameter of pile = 403 mm, the center to center spacing of the piles is 700 mm. The clay layer properties, Cu = 60 kN/m2, saturated unit weight = 18.33 kN/m3 Solve the questions 5 - 8. Find the empirical adhesion factor (a) * 1 0.92 0.82 0.74 0.62 None of the above.
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the minimum pile spacing in order to achieve 100% efficiency?
A 5 x 5 group piles of 0.4 m diameter displacement piles are to be constructed. The spacing between piles is 3D center to center. The thickness of the pile cup is 1.2 m and extends 0.5D from each side. The length of the piles is 20 m. The down word service load is 1000 ton. Use 2:1 method to compute the consolidation settlement under this load. Properties of the normally consolidated clay layer follows: Depth of the clay layer from ground surface to rock layer is 30 m. e= 0.5, c = 0.2
Solve this A group of nine piles, 12 m long and 250 mm in diameter, is to be arranged in a square form in a clay soil with an average unconfined compressive strength of 60 kN/m². Work out the centre to centre spacing of the piles for a group efficiency factor of 1. Neglect bearing at the tip of the piles. [Assume adhesion factor, a = 0.9]