A generation station of 10MW supplied a region which has the following demands: From To Demand (kW) Midnight (12.00AM) 3 AM 200 3 AM 5 PM 700 5 PM 7 PM 100 7 PM 10 PM 900 10 PM Midnight (12.00 AM) 200 Neglect transmission line losses and find the following Plot the daily load curve and the load duration curve. Find the load factor, the reserve capacity, plant capacity factor and the plant use factor.

A generation station of 10MW supplied a region which has the following demands: From To Demand (kW) Midnight (12.00AM) 3 AM 200 3 AM 5 PM 700 5 PM 7 PM 100 7 PM 10 PM 900 10 PM Midnight (12.00 AM) 200 Neglect transmission line losses and find the following Plot the daily load curve and the load duration curve. Find the load factor, the reserve capacity, plant capacity factor and the plant use factor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.18P

See similar textbooks

Related questions

Q: Calculate the capacitance of a single phase 50 Hz overhead line 40 km long consisting of two…

Q: Consider a 3-phase, 50 HZ, 11 KV distribution system. Each of conductors is suspended by an…

A: The operating line voltage is given as 11kV then the phase voltage:

Q: OR e) What is BILS? Explain their significance in power system studies.

A: BILS : BIL is stand for basic level insulation which is also known as lighting impulse voltage or…

Q: b. Two 1-ph transformers 6000/400V, the first 200kVA and the other is 350kVA when performing the…

A: Given Parameters of single phase transformers.we need find the load shared by the two transformers.…

Q: 3. A yearly load duration curve of a gas turbine power plant is a straight line from 50,000 to 5,000…

A: A)Installed capacity=2×30000+20000Installed capacity=80000 kW

Q: Low lagging power factor results in large voltage drop which results in poor.......... .…

A: we need to find the fill in the blank stated that ,Low lagging power factor results in large voltage…

Q: Trafo 020 j0.%2 0.20 0.250 j0.82 0.252 1550n 3.34LN j5502 3.34n

Q: most st algus 1. A three-phase load draws 720 kW from the grid with 0.8 lagging power factor. The…

Q: Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The…

A: The circuit diagram of a certain load is presented below. Determine the following: a. The power…

Q: A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The…

Q: 21. The total power drawn by two-impedance load in parallel is 15kW at 85% power factor lagging,…

A: The solution can be achieved as follows.

Q: Which of the following statements about next-generation wind energy is correct? a. They will have a…

Q: The impedance ZL in the circuit shown in Figure is adjusted for maximum average power transfer to…

A: (a) Remove the load impedance from the circuit and draw an equivalent circuit including the mutual…

Question

A generation station of 10MW supplied a region which has the following demands:

From	To	Demand (kW)
Midnight (12.00AM)	3 AM	200
3 AM	5 PM	700
5 PM	7 PM	100
7 PM	10 PM	900
10 PM	Midnight (12.00 AM)	200

Neglect transmission line losses and find the following

Plot the daily load curve and the load duration curve.
Find the load factor, the reserve capacity, plant capacity factor and the plant use factor.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
....
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
electrical engineering department plzz solve
A generating station has a connected load of (45MW) and a maximum demand is (15MW). with average demand of (6300KW), the value of demand * factor and load factor are 0.55, 1.5 0.33 ,0.42 O 3,0.14 O
6. If a power system has 10,000 kVA capacity, operating at 0.7 lagging power factor and cost of synchronous capacitors to correct the p.f is $10.5/kVA.Determine the cost involved and also required leading reactive power to increase the power factor to (a) 0.85 lagging p.f
For all of the Questions use 4 most significant digits after the decimal point (e.g.: ) 1. A three-phase load draws 720 kW from the grid with 0.8 lagging power factor. The load is balanced and star connected. For reactive power compensation, a bank of capacitors is connected in star across the load terminals. With this compensation, active power loss across the lines is reduced 10% (Meaning that If the power loss is 1 unit before compensation, power loss is 0.9 unit after compensation). Assuming that compensation does not change the load terminal voltage, calculate a) b) c) The kVAr rating of capacitors in each phase The improved power factor The new power factor if the same bank of capacitors is connected in delta Hint: The power loss across the line is proportional to the line current and hence the apparent power.
The per unit impedance of a generator on a 60 MVA, 20 kV base is j0.09 p.u. The per unit impedance to a 100 MVA, 20 kV base will be (a.) j0.054 p.u. (c.) j 1.5 p.u. (b.) j0.54 p.u. (d.) j0.15 p.u.
A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge impedance for the overhead line and cable are 400 ohms and 50 ohms respectively. The magnitude of the surge transmitted through the cable is ?
A system consists of four idenital 400 MVA generating units feed- ing a total load of 1016 MW. The intertia constant of each unit is 5 on 400 MVA base. The load changes by 1.5% for a 1% change in frequency. When there is sudden drop in load by 16 MW, obtain the power system time constant (T) with constants H and D expressed on 1600 MVA base.
21. The total power drawn by two-impedance load in parallel is 15kW at 85% power factor lagging, it's being supplied by 230- volts AC source. One of the loads (Load 1) takes 11KVA at 90% power factor leading. a. What is the real power, reactive power, and the apparent power of the unknown impedance (Load 2)? b. Find the resistance and the reactance of the other impedance load (Load 2). c. Determine the currents on each branch and the total current
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…