A gas in a piston-cylinder assembly undergoes an expansion process for which the relationship between pressure and volume is given by pV" = constant. The initial pressure is 3 bar, the initial volume is 0.1 m3, and the final volume is 0.2 m3. Determine the work for the process, in kJ, if (a) n = 1.5, (b) n = 1.0, and (c) n= 0.

A gas in a piston-cylinder assembly undergoes an expansion process for which the relationship between pressure and volume is given by pV" = constant. The initial pressure is 3 bar, the initial volume is 0.1 m3, and the final volume is 0.2 m3. Determine the work for the process, in kJ, if (a) n = 1.5, (b) n = 1.0, and (c) n= 0.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, end A and end B. A collar is located in the center of the rod. The initial temp is 60 degrees C. The final temperature is 35 degrees C. Determine the force that must be applied to the collar so that the reaction at B is zero.Given:Delta T=25 degrees CE for A36 steel: 200 GPaCoeff of thermal expansion: 12(10^-6)/degree C
An open tube is attached to a tank as shown. A). If Liquid X (Oil SG=0.55) rises to a height of 800 mm in the tube, what is the pressure Pa (in kPa) of the air above water? Neglect capillary effects in the tube. B). If Liquid X (Alcohol SG=0.79) rises to a height of 800 mm in the tube, what is the pressure Pb (in kPa) of the air above water? Neglect capillary effects in the tube.
If the fluid is contained in a long, narrow vessel so it can expand in essentially one direction only, show that the effective coefficient linear expansion a is approximately equal to the coefficient of volume expansion b?
An aluminum pipe has a length of 59 m at a temperature of 11°C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (in degrees Celsius) will the aluminum pipe be 16 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are a, = 23 x 10-6/0C and as = 12 x 10-6/0C, respectively. Also assume that the temperature of both pipes change equally.) °C
Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft •(1) ↓² -0.12 ft -0.1 ft -free jet ft³/s lb/ft²
A U-tube of uniform cross-section has both arms open to the atmosphere. The U-tube contains three immiscible liquids, with density PA, PB, and pc, as depicted in the diagram below, where po is the atmospheric pressure. We denote h to be the depth of the open surface of liquid A on the left arm, relative to the open surface of liquid Con the right arm. I is the depth of the interface between liquid B and C on the right arm and 2l is the depth of the interface between liquid A and liquid B on the right arm. Po PA (c) Po PC PB е е (a) Explain why the liquid densities need to satisfy the condition PA PB PC. (b) Write down an expression for the pressure at depth z below the surface of liquid A in the left-hand part of the tube. Show that l < h < 2l if PB + PC < PA•
The energy equation contains the following term(s): O pressure term (expansion/compression work) O velocity term (kinetic energy) elevation term (potential energy) all of the above
Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F liquid (brine) liquid (brine) -20 Ice + salt -30 NaCI 10 20 30 H2O 100 90 80 70 FIGURE P2.33 Composition, weight % a. Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. b. At a salt composition of 10%, what is the temperature at which ice will start melting? c. What is the eutectic temperature of the ice and salt combination? Temperature, °C
Problem # 1: The two rods as shown in the figure are attached to each other and the aluminum rod is fixed at the wall. The rods are initially unstressed and then a 20, 000 lb horizontal force is applied to the end of the brass rod as shown. Additionally, the rods experience a temperature increase of 80 °F. Use Linear coefficient of Expansion: Aluminum 13 x 10-6/°F Brass = 11 x 10-6/°F Young's Modulus: EAluminum = 10 x 106 lb/in2; EBrass = 15 x 106 lb/in² Determine; a) the final stress that develops in the aluminum rod, b) the total displacement of point C. Aluminum 10 ft B Aal- 2in² Brass 6 ft C 2 1in² Abr F = 20,000 lb
1. A bar with a constant cross section A is fixed at both ends. The bar is made of two different materials, that are joint together at point C. a) What are the reaction forces, if an external force F is applied at point C? b) Determine the normal force that is caused by a pure heating by AT. Given: Es Eat ast - 1 SAINT LC = 3, Steel Aluminiun
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E-30,000 ksi, E10,000 ksil. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assombly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips 18 kips 34 kips 60 in. 40 in. 30 in.