A gas flows through a square conduit. At one point along the conduit, the conduit sides are 0.100 m, the velocity is 7.55 m/s, and the gas's mass density is (for its pressure and temperature) 1.09 kg/m^3. At a second point, the conduit sides are 0.250 m, and the velocity is 2.02 m/s. Find the (a) mass flow rate (kg/s) of the gas and (b) its mass density (kg/m^3) at the second point. Cross-Section 1 Elevation View Cross-Section 2

A gas flows through a square conduit. At one point along the conduit, the conduit sides are 0.100 m, the velocity is 7.55 m/s, and the gas's mass density is (for its pressure and temperature) 1.09 kg/m^3. At a second point, the conduit sides are 0.250 m, and the velocity is 2.02 m/s. Find the (a) mass flow rate (kg/s) of the gas and (b) its mass density (kg/m^3) at the second point. Cross-Section 1 Elevation View Cross-Section 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of the three forces. Show complete solution and Draw FBD.
SHOW FBD
Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm is :(0 = = 0°)
include the figure in solution
show complete soln and clear FBD
A two-dimensional conduit has the velocity distributions shown in figure (a) and (b). Calculate the kinetic energy correction factor a for these distributions. U₁ (a) B ← NI3- (b)
There two parallel discs, one is up and another is down, whose diameters are both d. The thickness of the gap between the two discs is ô. The dynamic viscosity coefficient of the liquid in the gap is µ. The below disc is fixed. The above disc rotated around the axis at the angular velocity o. How much is the torque to make the disc rotate?
Hello please solve problem 4
A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter [Est =30,000 ksi, Eat =10,000 ksi]. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips (1) (2) (3) D B 34 kips 18 kips 60 in. 40 in. 30 in.
(b) An incompressible viscous liquid flows down a plate inclined at angle 8 as shown in Figure 4. The flow is assumed to be steady and the film thickness is constant. The density of the liquid is p, its dynamic viscosity is μ and the film thickness is h. Y₁ 0 0 8 ↓ 11 Figure 4 (i) Show that the governing equation for the velocity u(y) can be written as: ² pgsine = Əy² fl (ii) What are the boundary conditions at y = 0 and at y = h ? (iii) The velocity u(y) can be written as expression for C. (iv) What is the average velocity of the liquid film for unit depth (into paper)? u(y) = Cy(2h - y). Determine the
The uniform bar and the homogeneous cylinder each have a mass of 24 kg. The static coefficient of friction is µ, at A, B, and C (the three points of contact). (a) Assuming equilibrium, calculate the normal and friction forces at A, B, and C. (b) What is the smallest value of us necessary for equilibrium? Answer: Figure P 7.14 a) NA = 94.2 N, NB = 141.2 N, NC = 377 N. (b) 0.50 15m 0.333 m
7. An ejector mechanism consists of a helical compression spring having a spring constant of k = 98.1 kN/m. It is precom-pressed by 100 mm from its free state. If it is used to eject a mass of 100 kg held on it, the mass will move up through a distance of (a) 100 mm (c) 581 mm Mass Spring (b) 500 mm (d) 1000 mm