A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b= 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. A X b B

A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b= 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. A X b B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Dimensions in mm 800 N 425 250 150

A: Break the compound beam into parts consisting of each of the straight components.Show the complete…

Q: The Reactions are Given. Draw the Shear and Moment Diagrams and deflection diagram

A: Consider a section at a distance of x from the left end of the beam. For a section AB of the beam,…

Q: Solve for the Following Shear force equation for segment AB. a.-16.65 psf X squared b. 16.65 psf…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Q: Note that x = 0 at support A. When entering your answers, use the bending-moment sign convention…

Q: For the direct shear example shown below, if F = 47 kN, AAB = AcD = 3151 mm², the average shear…

A: Given:Force acting, F=47 kNArea of the surface, AAB=ACD=3151 mm2

Q: mplete shearing force and

Q: 2. For the simply supported beam subjected to the loading shown, (a) Derive equations for the shear…

Q: Question 2 Shear Stress AT shaped beam is fabricated from two sections of timber nailed together as…

Q: 600 N/m A B В D |C |-1 m--1 m --1 m --- -1.5 m- →-.5 m- 900 N

Q: The beam cross-section shown in the Figure Q6 is subjected to a resultant internal vertical shear…

Q: Question 1 Pulleys A and B with the dimension of 66 mm in diameter are connected to solid shafts AB…

Q: a.Identify all the equations that describe the shear over any portion of the beam. Solve the problem…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

So 873.7 it’s wrong . Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work

Topic: Shear and Bending Moment
A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front
axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B)
carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the
bending moment and enter your answer in N-m units..
Remember to also show all your work (FBDs, calculation steps, etc on the handworked file)
HINT: Determine the shear and bending moment equations along the beam. Assume only
concentrated loads at the front and rear axles.
A
X
b
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data.

VIEW

Step 2: Draw the free-body diagram of the beam.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem #8: For the beam and loading shown below compute the state of stress at point B (components of the 3x3 matrix), report your answer in ksi to two decimal places. 1.5 in 1.5 in B l in F= 5 kip 3 in 1 in 15 in Fx = 4 kip 3 in Fy = 3 kip
Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w=6.0 kips/ft, a=5.0 ft, and b-17.0 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Calculate the reaction forces B, and C, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since B, = 0, it has been omitted from the free-body diagram.) A Answers: By= C₂ = i a Save for Later Part 2 B, eTextbook and Media Answers: B B (a) V= (b) V= # (c) V= (d) V= kips Determine the shear force acting at each of the following locations: (a) x = 5.0-ft (i.e., just to the left of support B) (b)x= 5.0+ ft (i.e.. just to the right of support B) (c)x=21.0ft (d) x = 22.0-ft (i.e., just to the left of support C)…
Part 1 ✓ Correct For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-2.00 m, b-5.75 m, PA-70kN, and Pc 100kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. P₁ Calculate the reaction forces By and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since B, O, it has been omitted from the free-body diagram.) y a Answers: 0,- B. 113871 56.129 8 b KN KN 4 Pe -I D D D₂ Part 2 ✓ Correct Determine the shear force acting at each of the following locations: (a) x-1 m (b)x=4m (c) x = 8.75 m Note that x = 0 at point A. When entering your answers, use the shear-force sign convention detailed in Section 7. Answers: (a) V= (b) V= (c) V- -70 43.871 -56.129 KN…
3. Draw a schematic of the standard convention for the meaning of positive shears and bending moments (see Section 8.2). Use your diagram to help you answer 4 And 5. 4. Determine the internal shear at a section passing through point D. 5. Determine the internal bending moment at a section passing through point. The answers should be according to the answer key- 4. VD = 2000 lb (up) 5. MD = 1556 N-m (clockwise)
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy
Needs Complete typed solution with 100% accuracy.
Solve it correctly please. I will rate accordingly
FIGURE PS-66 500 N/m 0.60 m 1 Compute tbe reactions at the supports using the toch niques shown in Section 5-2, 2 Draw the complete shearing force and bending noment dagrams using the techniques shown in Sections 5-3 through 5-8, 3. Determine the magnitude and location of the maximum absolute value of the shearing force and bending moment
What is the over-turning moment at x = 0, of a hollow tube that has an OD of 40 mm, and an ID of 20 mm. The length of the tube is 960 mm. It is attached to a 1 inch thick plate.
Solve for the Following Shear force equation for segment AB. a.-16.65 psf X squared b. 16.65 psf X squared c. -16.75 psf X squared d. 16.75 psf X squared Bending moment equation for segment AB. a.-5.40 psf X cube b. 5.45 psf X cube c. -5.55 psf X cube d. 6.55 psf X cube Shear force equation for segment BC. a. 2000 lb - 200 lb/ft ( X) b. 2100 lb - 300 lb/ft ( X) c. 2150 lb - 300 lb/ft ( X) d. 3000 lb - 200 lb/ft ( X)
1. (a) Draw complete shear force and bending moment diagrams. (b) If x = 0 is at point "A", write equations for the shear force and bending moment, and indicate the appropriate sections. 10 kN 20 kN B k3 m 4 m 3 m D 5 m 15 KN E
PLEASE SHOW THE COMPLETE SOLUTION. CORRECT ANSWERS ARE SHOWN BELOW FOR YOUR REFERENCE. THANK YOU!