A frustum-shaped body is rotating at a constant angularspeed of 200 rad/s in a container filled with SAE 10W oil at 20°C (u = 0.1 Pa.s), as shown. If the thickeness of the oil film on all sides is 1.2 mm, determine the power required to maintain this motion. Also determine the reduction power input when the oil temperature rises to 80°C (u = 0.0078 Pa.s) Case SAE 10W oil D= 12 cm L= 12 cm d=4 cm

A frustum-shaped body is rotating at a constant angularspeed of 200 rad/s in a container filled with SAE 10W oil at 20°C (u = 0.1 Pa.s), as shown. If the thickeness of the oil film on all sides is 1.2 mm, determine the power required to maintain this motion. Also determine the reduction power input when the oil temperature rises to 80°C (u = 0.0078 Pa.s) Case SAE 10W oil D= 12 cm L= 12 cm d=4 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

M3
Ql:- A 300 mm diameter of pipes and 350 mm long slides along a large diameter cylinder at a speed of 1.64 ft/s under the application of a force of 25 N in the inverse direction of its motion due to a film of oil between the cylinder and pipe. If the viscosity of oil 5 stokes and s.g 0.89, find the thickness of oil and the diameter of cylinder. Q2:- A- Calculate the capillary effect in a glass tube of 0.24 in diameter when immersed in mercury, of r.d is 13.6. Assume o to be 0.5 N/m for mercury. The contact angles for mercury is 130..
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It has an absoluteviscosity of 1.50 Pa-s and a specific gravity of glycerin = 1.26.3. Solve for the coefficient of pipe friction
(a) The speed of an aircraft flying at an altitude of 11 km is measured by a pitot-staticprobe. If the differential pressure reading is 12.9 kPa, determine the speed of theaircraft in km/h. Take the density of air to be 0.4135 kg/m3
The thrust of a shaft is taken by a collar bearing filled with a forced lubrication system which maintains a film of oil of constant thickness 0.3 mm between the surface of the collar and the bearing. The outer and inner diameters of the collar are 156 mm and 120 mm respectively. The coefficient of viscosity of the oil is 1.2 poise. Calculate the power lost in friction of the bearing when the shaft rotates at 500 revolutions per minute.
Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft •(1) ↓² -0.12 ft -0.1 ft -free jet ft³/s lb/ft²
7. What is the pressure value (PA) needed to achieve equilibrium for the figure shown (kPa)? a. 0.59 c. 1.02 b. 1.02 d. None of all these PA S.G=0.87 30 120 mm
Problem A gas weighs 16 N/m³ at 25°C and at an absolute pressure of 0.25 N/mm². Deter- mine the gas constant and density of the gas.
In the figure show, a long uniform rod of uniform cross-section is partially submerged in 3 fluid layers. L1 2m, SG1 -3.0 & L2 3m, SG2 4.0 and L3-4m, SG-5.0. Find the exposed length in m if the SG of the rod is 4.0. Exposed Length SG, SG, SG3