A frame ABC is supported in part by cable DBE that passes through a frictionless ring at B. Knowing that the tension in the cable is 385 N, determine the components of the force exerted by the cable on the support at D. After solving, go back to the problem and check/evaluate the components determined if they have the right values. y 510 Z 480 280 B 210 600 400 Dimensions are in mm

A frame ABC is supported in part by cable DBE that passes through a frictionless ring at B. Knowing that the tension in the cable is 385 N, determine the components of the force exerted by the cable on the support at D. After solving, go back to the problem and check/evaluate the components determined if they have the right values. y 510 Z 480 280 B 210 600 400 Dimensions are in mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar AD is hanged by two steel cables of diameter 0.065 in as shown in the figure. Find a) The tension force in the cable BE and cable CF when P-220 lb b) The deflection at Point D (0) Est=29*10 Psi 8 in P. 10 in B D 12 in 12 in 12 in
Problem 6: Replace the two forces and the negative wrench by a single force R applied at A and the corresponding couple M. 100 130 700 N 500 N 25 N-m 60 14 40 D B 80 mm mm C mm 45 600 N 120 mm 40 mm
Value of uk=0.2. please read statement carefully. dont copy paste wrong answers
The rigid beam shown in the Figure is fixed at the top by two posts (dext = 40mm), one in AISI 4340 steel and the other in 6063-T6 aluminum. The posts are 500 mm long when no load is applied to the beam. Calculate the longitudinal displacements (δAl , and δFe) and the half stresses (σAl , and σ Fe) in the posts. Determine the angle of inclination of the beam (in degrees) when a homogeneously distributed load of 400 kN/m is applied. Calculate the factors of safety. Use E Fe = 200 GPa , and Eal = 70 GPa. Elastic limit AISI 4340 (Sy = 786 MPa), and AA6063-T6 (Sy = 214 MPa) (answers:/ δAl = -1.14 mm ; δFe = -0.40 mm σAl = -159 Mpa ; σFe = -159 Mpa ; angle ≈ 0.04° FSAL = 1.3 FSFE = 4.9)
Find the smallest square beam section that can be loaded as shown in the figure if τ<= 1.0 MPa and σ <= 8.0MPa. A is a hinge connection while B is roller support.
Please solve the question below step by step A) Draw the shear and moment diagram. Determine and label where is the critical point occurs. B) Calculate and show that the beam is safe and can withstand the load. ( List down all the assumption made ) C) Explain the function of the beam as shown in figure.
Show all the step in finding the answer. (Show step by step solution in order to be understood )
A 19-mm-diameter steel [E = 202 GPa: 0 = 11.1x10-6/°C] bolt is used to connect two rigid parts of an assembly. The bolt length is a = 175 mm. Determine the minimum clamping force that must be provided by the bolt when T1 = 21°C so that the clamping force it exerts when T2 = 58°C is at least 2.1 kN.
The square steel plate has a mass of 1970 kg with mass center at its center G. Calculate the tension in each of the three cables with which the plate is lifted while remaining horizontal.
A beam is subjected to equal bending moments of M, = 4200 N-m. The cross-sectional dimensions are b = 105 mm, c = 30 mm, d = 73 mm, and t = 8 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M2 Н d (typ) K b
2.F6 A container of mass m = 120 kg is supported by three cables as shown. Draw the free- body diagram needed to determine the tension in each cable. 360 mm 500 mm Z D y A B 450 mm 600 mm 320 mm X
Text: A beam is clamped at A. The beam is supported by a uniformly distributed load and a concentrated load as indicated on the sketch. The beam is made using the HE220A profile. The length of the beam is 4200 mm. and has a modulus of elasticity on it 2,0x105N/mm2 A) Calculate the bearing reactions of the beam for the given external load action. B) Establish moment and shear diagram for the beam for the given external load action. C) Calculate the transverse displacement of the free (cantilevered) end for the given external load action. D) Calculate the rotation of the free (cantilevered) end for the given external load action.