a:- Forming turning process is used to produced products with large dimensions? b:- EDM process is used to machining of ceramic.? c:- Removal of metal is done by the face of cutting tool in horizontal milling?

a:- Forming turning process is used to produced products with large dimensions? b:- EDM process is used to machining of ceramic.? c:- Removal of metal is done by the face of cutting tool in horizontal milling?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.3: Cnc Turning: Programming

Problem 7RQ: If a G1 code command is programmed partway through a machining operation, but no F-value is given in...

See similar textbooks

Similar questions

Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
$i1. Match List I List II A. Die-sinking B. Deburring C. Fine hole drilling (thin material) D. Cutting/hardening sharp materials 1. Abrasive jet machining 2. Laser beam machining 3. EDM 4. Ultrasonic machining 5. Electrochemical grinding Codes : A B C D (a) 3 4 1 (6) 2 4 3 (c) 3 1 5 (d) 4 1 3 (Ruonorty conferred on steel by the
2. Write a complete program to mill around the part. The endmill is .500 diameter, and you want to leave .010 stock for a finish pass. Enter a diameter offset number (Dn) command for tool DIAMETER Geometry of .520 for machining a roughing pass around part. And then define another pass around part using the same program coordinates but a different diameter offset number (Dn), and enter in the correct diameter offset value of .500 to machine part to the finish size. TOOL 1 has 0.520 in D21 and 0.500 in D01 Tool Speed (rpm) Feed (ipm) Operation Finish outside contour, x .50 deep Tooling 1 .5D endmill 1200 6. 25 R.25 2 PL. R .50 2.00 XO YO 4.0 SO. 1.0 SQ. 5 DA. EM 1.250- X-2.5 Y-2.0 START POINT
6. Write one block of code to perform the indicated operation. Assume the location is X2.0, Y2.0, and the depth is Z-1.5 for each operation. 1) Drill with dwell of 0.2 seconds 2) Peck drilling cycle with a 0.15" peck depth 3) Chip breaker with a 0.15" peck and full retract every 0.6" 4) RH tapping cycle for 14-16 NC thread; define a spindle speed and feed 5) Bore a hole with the tool being retracted manually
How many cutting-plane lines are shown on this print?
Please give correct answer , previous answer was wrong nd don't copy
Make the part program using CNC code. Tool Dia. = 6 mm depth of cut 3.0 mm (Use G90 code) (follow the points as marked Start point, P1, P2, P3, P4, P5, P6) (don't use G41, G42)
I need these three parts answered, if you can not answer all three parts please leave it for another tutor, thank you.
Q1) For the Lath Machine operations shown in the table below: > Write the operation name > Locate and place the arrows showing the process variables in machining (v, f, d) on the operation sketch, stating process var.ables name. > State the parts in lathe machine that is responsible (provides) the motion for each variable, following the solved example. process variables Lathe part provide Operation sketch name motion Cutting speed (V) Headstock Velocity f Depth of cut (f) Feed rate Cross slide Tool Feed Depth of cut (d) Carriage Example Operation name : Straight turning WORK PECE Operation name : Operation name :
Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS drill bit and T2 is a 0.5" tapping bit. The rest of the features are cut using a 0.75" HSS milling tool, T3. Feed rate and spindle speed are 10 ipm and 2000 rpm. The material is low- carbon steel. Part thickness is 0.5”. Use dotted lines two show the path of tools movements. Set up proper operation conditions as discussed in the class today.
The following jobs are waiting to be processed at a small machine center: JOB 10 20 30 40 50 DUE DATE 260 254 260 265 275 days (round your response to one decimal place). days (round your response to one decimal place). DURATION (DAYS) 18 T 22 14 32 All dates are specified as manufacturing planning calendar days. Assume that all jobs arrived on day 200 (yesterday) in the order shown but are not scheduled to begin until day 201 (today). a) Sequence the jobs according to LPT. According to the LPT rule, the sequence of jobs should be 50, 20, 10, 30, 40 b) What is the average completion (flow) time? The average completion (flow) time is c) What is the average job lateness? The average job lateness is d) What is the average number of jobs in the system? The average number of jobs in the system is jobs (round your response to one decimal place). 62446
Sub-parts d) and e) please