Vrite a complete program to mill around the part. The endmill is .500 diameter, and yo nt to leave .010 stock for a finish pass. Enter a diameter offset number (Dn) command for too AMETER Geometry of .520 for machining a roughing pass around part. And then define other pass around part using the same program coordinates but a different diameter offset amber (Dn), and enter in the correct diameter offset value of .500 to machine part to the finish ze. TOOL 1 has 0.520 in D21 and 0.500 in D01 Tool Speed (rpm) Feed (ipm) Operation Finish outside contour, x .50 deep Tooling .5D endmill 1200 6.

Vrite a complete program to mill around the part. The endmill is .500 diameter, and yo nt to leave .010 stock for a finish pass. Enter a diameter offset number (Dn) command for too AMETER Geometry of .520 for machining a roughing pass around part. And then define other pass around part using the same program coordinates but a different diameter offset amber (Dn), and enter in the correct diameter offset value of .500 to machine part to the finish ze. TOOL 1 has 0.520 in D21 and 0.500 in D01 Tool Speed (rpm) Feed (ipm) Operation Finish outside contour, x .50 deep Tooling .5D endmill 1200 6.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answer fast you can!
Solve it quickly please now
What tool is used to put a radius on an existing intersection? Extend aut cad Trim move Fillet Chamfer * The copy command is used as a sub command to command the rotation to copy shapes -the original shape. aut cad - None of the above - with insert - with delete - with preserving without preserving
CNC. Help please
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"
Don't solve handwritten
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
Which of the following commands will move the tool in a diagonal line at a feed rate of 5 from position (10, 20), assuming absolute programming mode is active? Select one: a. N10G00X10F5 b. N10G01X20Y30F5 c. N10G01X10F5 d. N10G00X20Y30F5
Please help
Make sure to draw the tool path
Fill in the data needed in the table RPM FEED LENGTH OF CUT CUTTING TIME 325 0.006 6. 6 1/8 74 0.010 2 7/8 130 0.008 1 1/2
10q In down milling, the workpiece is feed against the rotation of the milling cutter to produce a flat surface. Select one: True False