A) For the soil profile shown in Fig. (2), determine: 1) Effective stress at point A. 2) Piezometric reading at point B. 3) Seepage force per unit volume. 4) Piezometric reading for quick condition (boiling).

A) For the soil profile shown in Fig. (2), determine: 1) Effective stress at point A. 2) Piezometric reading at point B. 3) Seepage force per unit volume. 4) Piezometric reading for quick condition (boiling).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A) The results of two consolidated-drained triaxial tests on clay are given below in Table 2. Table 2: Results of CDT tests. Specimen Chamber Pressure I II 3, kPa 110 220 Deviator Stress 01-03, kPa 220 400 a) Calculate the shear strength parameters of the soil. b) What are the normal and shear stresses on a plane inclined at 38° to the major principal plane for Specimen I? c) What are the normal and shear stresses on the failure plane at failure for Specimen II? B) The laboratory test results of a standard Proctor test are given in the following table.
A soil profile consists of sand (5-m thick) which overlies a layer of clay (4-m thick). Ground water table is located at the interface of the sand and clay. The effective stress at the bottom of the clay layer was determined. If the water table rises to the top of the ground surface, what is the change in the effective stress (in kPa) at the bottom of the clay layer? For sand layer: Void Ratio = 0.82, Specific gravity = 2.75, Degree of Saturation = 0.76 For clay layer: Void Ratio = 1.09, Specific gravity = 2.76
A soil profile is shown in figure below. Calculate the following:a. Effective stress at point A in kPa.b. Effective stress at point B in kPa.c. Effective stress at point C in kPa.
11. J The effective stress friction angle of a saturated, cohesionless soil is 38°. The ratio of shear stress to normal effective stress on the failure plane is (A) 0.781 (B) 0.616 (C) 0.488 (D) 0.438
A sample of soil (0.1 m X 0.1 m) is subjected to the forces shown in Figure below. Determine (a) σ1, σ3, and α;(b) the maximum shear stress; and (c) the stresses on a plane oriented at 30° counterclockwise from the major principal stress plane.
7.12 A sand specimen was subjected to a drained shear test using hollow cylin- der test equipment. Failure was caused by increasing the inside pressure while keeping the outside pressure constant. At failure, o, = 193 kN/m² and o; = 264 kN/m². The inside and outside radii of the specimen were 40 and 60 mm, respectively. (a) Calculate the soil friction angle. (b) Calculate the axial stress on the specimen at failure.
Problem 2 Plot the stress profile for total stress, effective stress, and pore water pressure. Show all calculation. Diy sand 0.61 Saturated sand 0.48. G-267 Clay
Question 20 A soil profile consists of sand (5-m thick) which overlies a layer of clay (9-m thick). Ground water table is located at the interface of the sand and clay. The effective stress at the bottom of the clay layer was determined. If the water table rises to the top of the ground surface, what is the change in the effective stress (in kPa) at the bottom of the clay layer? For sand layer: Void Ratio = 0.82, Specific gravity = 2.68, Degree of Saturation = 0.6 For clay layer: Void Ratio = 0.92, Specific gravity = 2.86 Round off to two decimal places.
A sand sample is subjected to direct shear testing. Two tests areperformed. For test 1, The sample shears at a stress of 2500 psf whenthe normal stress is 4000 psf.Test 2, The sample shears at a stress of 3500 psf when the normalstress is 6000 psf. Determine the following:a) Angle of Internal frictionb) Value of cohesionc) Compute the shear stress at a depth of 12 ft. if the unit weight ofthe soil is 150 pcf
A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. a. 177.38 b. 354.75 c. 88.69 d. 709.5
c. An undisturbed soil sample, 110 mm in diameter and 220 mm in height, was tested in a triaxial machine. The sample sheared under an additional axial load of 3.35 kN with a vertical deformation of 21 mm. The failure plane was inclined at 50° to the horizontal and the cell pressure was 300 kN/m². i. Draw the Mohr circle diagram representing the above stress conditions, and from it determine: - Coulomb's equation for the shear strength of the soil, in terms of total stress; - the magnitude and obliquity of the resultant stress on the failure plane. ii. A further undisturbed sample of the soil was tested in a shear box under the same drainage conditions as used for the previous test. If the area of the box was 3600 mm² and the normal load was 500 N, what would you expect the failure stress to have been?