A 2 m thick clay is singly drained. A structure founded on the surface applied an average stress increase of 50 kPa to this clay layer. A piezometer is installed at the mid-depth of the clay layer. A. What would you expect the initial excess pore pressure reading on the piezometer to be immediately after application of load? B. The piezometer recorded a pore pressure of 25 kPa, 1-yr after the application of the stress. What would you expect it to read 2 years later? What is the coefficient of consolidation of this clay in cm²/s? C.

A 2 m thick clay is singly drained. A structure founded on the surface applied an average stress increase of 50 kPa to this clay layer. A piezometer is installed at the mid-depth of the clay layer. A. What would you expect the initial excess pore pressure reading on the piezometer to be immediately after application of load? B. The piezometer recorded a pore pressure of 25 kPa, 1-yr after the application of the stress. What would you expect it to read 2 years later? What is the coefficient of consolidation of this clay in cm²/s? C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

11. J The effective stress friction angle of a saturated, cohesionless soil is 38°. The ratio of shear stress to normal effective stress on the failure plane is (A) 0.781 (B) 0.616 (C) 0.488 (D) 0.438
2- A three-axis compression test on a clay sample that is comprehensive and normal up to a stress of 300 kPa and a specific volume of 2 Consolidated is done, The values of q and volumetric strain are measured at axial strain, 0, 2 and 10 percent (failure) . The value of N is equal to 3 and A is equal to 0.2. Graph of all-round stress on initial all-round stress Draw the initial all-round stress in terms of section
Data from an oedometer test using a clay specimen are plotted in the graph shown below. If the compression index is equal to 0.6, calculate the void ratio (e2) missing at Point C, which is associated with a vertical effective stress equal to 105 kPa
Vane Shear Testing
4. Please answer parts a and b
Complete answer plss.
In an Oedometer apparatus, a specimen of fully saturated clay has been consolidated under a vertical pressure of 50 kN/m2 and is presently at equilibrium. The effective stress and pore water pressure immediately on increasing the vertical stress to 150 kN/m2, respectively are...?
Question 20 A soil profile consists of sand (5-m thick) which overlies a layer of clay (9-m thick). Ground water table is located at the interface of the sand and clay. The effective stress at the bottom of the clay layer was determined. If the water table rises to the top of the ground surface, what is the change in the effective stress (in kPa) at the bottom of the clay layer? For sand layer: Void Ratio = 0.82, Specific gravity = 2.68, Degree of Saturation = 0.6 For clay layer: Void Ratio = 0.92, Specific gravity = 2.86 Round off to two decimal places.
A saturated specimen of cohesionless sand was tested under drained conditions in a triaxial compression test apparatus and the sample failed at a deviator stress of 482 kN/m2 and the plane of failure made an angle of 60° with the horizontal. What would be the magnitude of the deviator stress in kPa at failure for identical specimen of sand if it is tested under a cell pressure of 200 kPa? a. 200 b. 241 c. 400 d. 600
In a consolidated undrained test with pore pressure measurement on a normally consolidated clay, a sample consolidated under a stress of 200 kPa failed at an additional axial stress of 150 kPa. The pore pressure at failure was 75 kPa. Determine analytically the shear strength parameters in terms of effective stresses.
A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. a. 177.38 b. 354.75 c. 88.69 d. 709.5