A fluid flow is given by : V = 10x'i – 8x'yj. Find the shear strain rate and state whether the flow is rotational or irrotational. [Ans. - 8xy, rotational]

Q: What is a transfer-type measuring tool?

A: Precision measurements are those with an accuracy of 0.5 mm or 1°. These measurements are necessary…

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: A plate boundary with sheer stress is known as _______   a. Divergent   b. Tectonic   c.…

A:

Q: write an introduction for hardness test lab

A: Hardness Measurement methods.

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: Scale board

A:

Q: A datum when used in manufacturing is primarily used for?

A: A datum in manufacturing is defined as the origin point, plane, or axis from which the geometric…

Q: why universal testing machine important (3-5 sentence ONLY)

A:

Q: Please answer print reading for industry 15-1 # 9, 12, and #15

A: 1) Yes, It is the detailed drawing of one part. This drawing do not have bill of material table. 2)…

Q: Endurance Limit calculations are suited for types of loading Random Static Impact Repeated and…

A: Endurance limit is the maximum value of the fully  reversed bending stress which a material can…

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: Open-die forging (upsetting) involves reduction of height of a specimen between two flat dies using…

A: Forging is the forming process in which metal is shaped by applying force using hammer or…

Q: Describe the concept of finding toughness using impact testing machine.

A:

Q: What is an indexing plate and indexing wheel?

A:

Q: What is the best way to test load/stress testing?

A: following is the answer to the above question-

Q: B: From figure 1, draw and explain the meaning of present symbol.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Where is a bent material most likely to fail?

A: Let us take an example. Consider any beam applied with external bending  moment . This beam…

Q: If FB = 830 N, Fc = 450 N, determine the magnitude of the resultant force at A. (Figu Express your…

A: Given FB=830NFC=450N

Q: Question 2: How long a wrench is needed to tighten a 9/16-inch bolt if the maximum force (pull) that…

A: Given: The diameter of bolt, d = 9/16 in = 0.5625 in The maximum force produced by mechanic, F = 75…

Q: What is rectification

A: Rectification is the conversion of alternating current to direct current. Rectification is performed…

Q: Digital Vernier Caliper is used to measure the force applied on the experimental specimen. T/F?

A: Digital Vernier Caliper A digital vernier caliper is a measuring instrument that is used to measure…

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: Is it possible for an item to fail yield but not fail fatek

A: Given question : Is it possible for an item to fail by yielding but not fail by fatigue.   .

Q: Successful re-engineering eliminate much monitoring checking, waiting, etc leaving more time for…

A:

Q: Steps how to draw a needle of a cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: The is the condition in which a feature of size contains the least amount of material within the…

A: Maximum material condition: The condition of the object in which the object have maximum amount of…

Q: 4. What is calibration?

A: Calibration is generally used in Instrument

Q: 3mm Imm 2mm 2mm 2mm

A: Let us divide the given figure into 3 sections as shown below – Section 1 is OBCO which is a…

Q: Draw and state Vernier Calliper Parts?

A:

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: es the specification "8.8" in the standard designation of a bolt mean? Specify values including…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: advantage and disadvantages of using STRAIN GAUGE

A: Given: Advantage and Disadvantages of using STRAIN GAUGE

Q: The most ductile structure is Pearlitic matrix with flaky graphite Pearlitic matrix with vermicular…

A:

Q: How does a strain gauge work?

A: Strain gauge: It is a sensor whose resistance varies with applied force. It then converts force,…

Q: Which fixture would be the most suitable for welding up and drilling the holes for fixture for the…

A: Modular fixture is most suitable for welding up and drilling the holes for fixture for the complete…

Q: Tool marks which are produced by force that are parallel to a surface are known as: Group of answer…

A: Tool marks which are produced by force that are parallel to a surface are known as Striated marks.

Q: what are some of the ways by which the blades of windmill be improved

A: Wind energy is an example of renewable energy and its use never harms the environment. But it is an…

Q: Which type of feature doesn't belong to orientation tolerances?         Concentricity…

A: using datum plane measure the Angularity , Perpendicularity and  Parallelism