A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape are shown in the second figure. Assume LAB= 6ft, Lec=2 ft. Lco=3ft, LDE 3ft, Pc-1990 lb, PE 1950 lb, WAB= 800 lb/ft, b₁ = 6 in., b₂= 2 in., b3-3 in.,d₁-2 in. d₂-6 in.d3 = 2 in. Consider the entire 14-ft length of the beam and determine: (a) the maximum tension bending stress of at any location along the beam, and (b) the maximum compression bending stress o at any location along the beam. A WAB LAB B จ b₁ Pc LBC C OD LCD -b₂ d₁ LDE d₂ PE E X

A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape are shown in the second figure. Assume LAB= 6ft, Lec=2 ft. Lco=3ft, LDE 3ft, Pc-1990 lb, PE 1950 lb, WAB= 800 lb/ft, b₁ = 6 in., b₂= 2 in., b3-3 in.,d₁-2 in. d₂-6 in.d3 = 2 in. Consider the entire 14-ft length of the beam and determine: (a) the maximum tension bending stress of at any location along the beam, and (b) the maximum compression bending stress o at any location along the beam. A WAB LAB B จ b₁ Pc LBC C OD LCD -b₂ d₁ LDE d₂ PE E X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please box the final answer
UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. SOLVE IN 2 DECIMAL PLACES. BOX THE FINAL ANSWERS.
Please answer correctly. Please I need this ASAP. thank you Note: The tolerance is ± 1 in the third significant digit
Determine the design strength of a T-Beam with the following data: b+= 700 mm bw = 300 mm hy = 100 mm d = 500 mm f₂ = 21 MPa fy = 414 MPa A: 5-20 mm dia.
I need the answer as soon as possible
Refer to the figure shown, if h1=150mm, h2=300mm, b=300mm, fc'=35MPa and fy=420MPa. Calculate the following gives the balanced steel area in mm2? h₁ As b h₂
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
Read the question carefully and give me the right solutions with clear calculation.
Question 16 A W10x30, 2.9 m long, A36 steel is used as a column with fixed ends to support a service dead load of 154 kN. Calculate the maximum service live load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN. A = 5,703 mm2 rx = 111.25 mm ry = 34.80 mm
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
steel The hollow section column, shown in the figure below, has a length of 18 ft, and it is made of steel with a yield strength of 50 ksi. The column is fixed at the bottom and pinned at the top. What is the capacity of this column under a pure compressive loading? |3/4 in 3/4 in 10 in 5 in
A frame structure is shown below. The links connected below is a bar with a 30mm by 60mm in section. Find the Allowable lad P that can be applied so that the stresses will not exceed 100MPa in tension or 80Mpa in compression.