A flanged bolt coupling has eight 10-mm diameter steel bolts on 600 mm diameter bolt circle and six 20 mm diameter bolts on 300 mm diameter bolt circle. Determine the maximum torque that can be applied without exceeding the shear stress of 55 MPa for the bolts and for the rods. Use G = 80 GPa.

A flanged bolt coupling has eight 10-mm diameter steel bolts on 600 mm diameter bolt circle and six 20 mm diameter bolts on 300 mm diameter bolt circle. Determine the maximum torque that can be applied without exceeding the shear stress of 55 MPa for the bolts and for the rods. Use G = 80 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a coupling with eight bolts. The bolt circle diameters are 5 and 10 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. O 0 600 rev/min Determine the minimum nominal shoulder diameter of a bolt if all bolts are to have the same diameter and not exceed a shear stress of 20 kpsi Select a preferred fraction size. The minimum nominal shoulder diameter of a bolt is, in.
The tube is made of C86100 bronze and has a rectangular cross section asshown in Figure. If it is subjected to the two torques, determine the average shear stress in the tube at points A and B. Also, what is the angle of twist of end C? The tube is fixed at E.
100 mm i 70 mm The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70MPA or an angle of twist of 2.50 in the 3.5m length. Use G = 83 GPa for steel. T 100 mm 70 mm 70 mm 1.5 m 2 m T
Six 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel and six 20 mm diameter bolt in the inner bolt circle of 260 mm diameterare aluminum. What is the torque capacity of the coupling? Assume thatthe allowable shearing stress for the steel bolts is 40 Mpa and aluminumbolts of 30 Mpa. The Shear modulus of elasticity of aluminum and steel are28 Gpa and 84 Gpa, respectively.
A flange bolt coupling consists of 10-15mm diameter steel bolts on a bolt circle 300mm in diameter and 6-15mm diameter steel on a concentric bolt circle 200mm in diameter. If the allowable shearing stress in the bolt is 50MPa, determine the number of 15mm steel bolts that must be used on the 200mm bolt circle of the coupling to increase the torque capacity to 20KN-m. Оа. 14 O b. 8 Ос. 12 d. 10
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tlow = 35 MPa and (Pacallow =2°, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L,, L,, and D. L1 L2 A 3T 2T Student L, D L, (m) ID (m) (mm) 1131731 0.6 78
The composite shaft consists of a mid-section that includes the 1-in. diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges. The shaft is subjected to a torque of T=950 lb-ft. The material is A-38 steel, G = 11 x 10³ ksi- (Eigure 1) T 1 in. 3 in. 0.25 in. 0.75 ft. B 0.5 ft Determine the angle of twist of end C of the shaft relative to end D.
A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 5°. T= 60 N.m (1) 1,800 mm 800 mm
The two shafts are made of steel (G=11x106 lb/in2). Each has a diameter of 1 in. , and they are supported by bearings at A, B and C, which allow free rotation. If the support at D is fixed, determine the angle of twist of end A when the torques are applied to the assembly as shown. Torque applied at H of 80 ft lbs, and at G of 40 ft lbs in opposing directions as seen in the figure
Two 20 mm steel shafts with a 100 MPa yield stress in shear are connected by a brass coupling with inner diameter 20mm. The brass has a 60 MPa yield stress. Determine the largest torque that can be applied to the shaft using a safety factor of 2.1 and the resulting outer diameter of the brass coupling needed for the same safety factor. Ans: d=268 mm 20 mm
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 320 N-m, Tc = 371 N-m, and TD = 181 N-m. TD (3) O -208 N-m O -224 N-m O -138 N-m O -190 N-m O -265 N-m Tc (2) B TB (1) TA
Refer to the table of equations upon answering the problem.