A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 300 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 193 mm in diameter. If the torque that can be applied is 7947 Nm without exceeding a shearing stress of 57.09 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.

A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 300 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 193 mm in diameter. If the torque that can be applied is 7947 Nm without exceeding a shearing stress of 57.09 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2.63 The bolt is subjected to the force F, which has components acting along the z. y, z axes as shown. Part A If the magnitude of F is 76 N, and ax=52° and y= 50°, determine the magnitude of Fz component. Express your answer to two significant figures and include the appropriate units. ANSWER: F₂ = 40 N Incorrect; Try Again; 4 attempts remaining Part B Determine the magnitude of Fy component. ANSWER: Fy= your answer to significant figures and inclu the appropriate units. Part C Determine the magnitude of F₂ component. Express your answer to two significant figures and include the appropriate units. ANSWER: F₂ =
SHOW COMPLETE SOLUTION AND SKETCH THE ILLUSTRATION
An A36 angle bar is used as a tension member connected on both legs with 20 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem What is the value of S if the joint is 80% efficient? Tension of Plates = 76 MPa Hole diameter (effective) = 23 mm
... 7.5 mm SN kN SN kN 12 mm 12 mm 7.5 mm 12.5 mm SN kN SN kN 18 mm 25 mm 18 mm On the above figure, determine the following: 1. Maximum bearing stress at joints ( bolts and plates). 2. Shearing stress If the bolts is in double shear. 3. Maximum average normal stress on the plates. Note: Round off your answer in two decimal places.
Question 4 On the figure below, determine the following: 1. Maximum bearing stress at joints ( bolts and plates). 2. Shearing stress If the bolts is in double shear. 3. Maximum average normal stress on the plates. 7.5 mm SN kN SN kN 12 mm 12 mm 7.5 mm 12.5 mm SN kN SN kN 18 mm 18 mm mm
7:49 ll ? 1 Gmail h.w. 1.jpg A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Fig. Axial loads are applied at the positions indicated. If P 3000N and the cross sectional area of the rod is 325 mm2, determine the stress in each section, and total deformation of the road. E for steel is 200000 MPa, E for aluminum is 70000 MPa, E for bronze is 100000 MPa 4P Steel Bronże O | Aluminum PO D.9 ~回

Question 27 An A36 angle bar is used as a tension member connected on both legs with 18 mm diameter bolts. Given that s = 65 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
An A36 angle bar is used as a tension member connected on both legs with 22 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 56 MPa, how many 18 mm-diameter steel bolts must be used on a 300 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft?
2. The A-36 steel Bar BC had a diameter of 40 mm before the two loads, P, were applied. If after loading, the new diameter of the bar is 39.995 mm, what was P? P -1 m B 0.75 m 1 m
I need the answer as soon as possible