A flange used to connect two pipes is shown in Figure Q3. Holes need to be drilled to fix it.Drilling should be done in two steps with each step 7 mm. Using absolute coordinate systemand the parameters given in the table below,(i)Determine the coordinates of hole H=4(ii)Determine the shortest distance between hole H=4 and the center(iii)Write a G code program for drilling hole H=4 only.CNC Drilling Operating ConditionsSpeed of the spindle1770 RPMFeed rate of drilling21 mm/minuteSize of the drill bit8 mmRack number of drill bit2Distance kept between the drill bit and the work piece surface 4.5 mmThe flange thickness14 mmH=2H=3H=1B=30°H=4A = 60°.angle = 0°.Center (0, 0)Radius = 60 mm%3DFigure Q3

pitch circle diameter (PCD) = 120 mm Angle with respect to holesat , H1 = θ = 60°at , H2 = θ =…

A flange used to connect two pipes is shown in Figure Q3. Holes need to be drilled to fix it. Drilling should be done in two steps with each step 7 mm. Using absolute coordinate system and the parameters given in the table below, (i) Determine the coordinates of hole H=4 (ii) Determine the shortest distance between hole H=4 and the center (ii) Write a G code program for drilling hole H=4 only. CNC Drilling Operating Conditions Speed of the spindle 1770 RPM Feed rate of drilling 21 mm/minute Size of the drill bit 8 mm Rack number of drill bit 2 Distance kept between the drill bit and the work piece surface 4.5 mm The flange thickness 14 mm H=2 H=3 H=1 B=30° H=4 A = 60°. angle = 0°. Center (0, 0) Radius = 60 mm %3D Figure Q3

A flange used to connect two pipes is shown in Figure Q3. Holes need to be drilled to fix it. Drilling should be done in two steps with each step 7 mm. Using absolute coordinate system and the parameters given in the table below, (i) Determine the coordinates of hole H=4 (ii) Determine the shortest distance between hole H=4 and the center (ii) Write a G code program for drilling hole H=4 only. CNC Drilling Operating Conditions Speed of the spindle 1770 RPM Feed rate of drilling 21 mm/minute Size of the drill bit 8 mm Rack number of drill bit 2 Distance kept between the drill bit and the work piece surface 4.5 mm The flange thickness 14 mm H=2 H=3 H=1 B=30° H=4 A = 60°. angle = 0°. Center (0, 0) Radius = 60 mm %3D Figure Q3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Help me with this ENGINEERING GRAPHICS problem.
Instructions: Search for the G and M codes description or function for the following. “Example: G00 –Rapid Traverse” CNC Milling G Code List G code DescriptionG00 G01 G02 G03 G04 G17 G18 G19 G28 G30 G40 G41 G42 G43 G44 G49 G53 G54 G55 G56 G57 G58 G59 G68 G69 G73 G74 G76 G80 G81 G82 G83 G84 G85 G86 G87 G88 G89 G90 G91 G92 G98 G99 CNC Lathe G Code ListG code DescriptionG00 G01 G02 G03 G04 G09 G10 G14 G15 G17 G18 G19 G20 G21 G28 G29 G31 G32 G40 G41 G42 G43 G50 G50 G52 G53 G54 G55 G56 G57 G58 G59 G61 G64 G65 G68 G69 G70 G71 G72 G73 G74 G75 G76 G80 G81 G82 G83 G84 G85 G86 G89 G90 G92 G94 G95 G96 G97 G98 G99 G100 G101 G103 G105 G107 G110 G111 G112 G113 G114 G115 G116 G117 G118 G119 G120 G121 G122 G123 G124 G125 G126 G127 G128 G129 G154 G156 G167 G170 G171 G172 G184 G186 G187 G195 G196 G198 G199 G200 G211…
In Autocad
How would you determine the magnitudes of the velocities of B and C at the instant shown? Draw all the related diagrams and indicate the directions of the vectors. Use Matrix no 9 from the table.
Calculate Centre of gravity for the following figure
Plz hand written otherwise skip.... If hand written i'll upvote plz fast plzzzzzz fast plzzzz
Q2: Write all the necessary steps to draw the following figure using relative coordinate system. For example; the draw of (L1, L2) as following > Dynamic input > of > Home> Draw> Line> 50,50>Enter>@100,0>Enter> @0,50 > Enter> and so on 100 100 100 100 A L1 L2 Start Point (50,50) 100 200 100 007 000 007
Anyone explain how to draw this in autocad, thanks
finishing the program of the part by using SKY CNC system format R4 2x45° 28 50 60 75 040 032 024
In figure below, what error results if the rod is held in position AD, and if AE= 5 meters and EB= 3 in.? Please write your answers on an A4 paper with your name, school number and signature to show the phases of solving. Afterwards, you can upload it on LMS system as pdf, jpeg, etc. Horizontal line E
Please Fill In the blanks where I have marked red X's using the questions and Image below. 1. On the drawing above, before any geometric controls are applied, what is the coaxility tolerance is implied between the diameters? 2. On the part above, apply datum feature symbols to create a datum axis A-B by using the right and left diamters. 3. Apply a position coaxility between the right and left diamter of 0.1 at MMC. 4. Apply a position tolerance to the large center diameter within a diameter of 0.3 in relation to the single datum axis established by both datum features A and B.
What is the correct command used for drawing a graph between two quantities in OCTAVE Software? O plot(x,y) O ylable(x,y) O graph(x,y) xlabel(x,y)