Question 5a) Finding ultimate loads stems from the variation of loading patterns. Explain how to obtainmaximum load for live load arrangement for a multispan beam. Illustrate with an example.b) Draw a qualitative influence line for the reaction at D, and bending moment at midpoint ofspan DE. For each of the influence lines, place live loads for maximum positive reaction andbending moment.3m2m2m2m2mFigure 11c) Draw the influence line of support reaction C for the beam in figure 12. El is constant.A.CT6m6mFigure 12月

a) There are various types of load are acting on a structure for example live load, dead load,…

Answered: a) Finding ultimate loads stems from…

a) Finding ultimate loads stems from the variation of loading patterns. Explain how to obtain maximum load for live load arrangement for a multispan beam. Illustrate with an example.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel beam has the cross section shown. The beam length is L- 7.8 m, and the cross-sectional dimensions are d - 335 mm, by - 200 mm, t- 12 mm, and t,- 10 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 150 MPa. Answer: Wo kN/m
PROBLEM 1: A reinforced concrete beam has a simple span of 8m. It carries a concentrated factored load, Pu, at midspan. The beam is reinforced with 3D25mm. It has a width of 300mm and an effective depth of 450mm. Neglecting the weight of the beam, and using the exact/detailed calculation for Vc, a. What is the ultimate shear capacity of concrete at a section 2m from the support? b. What should be the shear capacity of web reinforcement at the section 2m from the support? c. What is the maximum spacing of web reinforcement allowed by the code at the section 2m from the support if the diameter of stirrups is 12mm? d. What is the required spacing of web reinforcement at the section 2m from the support if the diameter of stirrups is 12mm? e. Draw the design details for shear of the beam from x-0m to x=2m.
You are designing a floor beam in an office building that must support a factored bending moment of M, Ed = 602.1 kNm Assume that the beam is Section Class 1, fully restrained and has a yield strength of 355 N/mm2 Based on stress, what is the minimum plastic section modulus that should be chosen? Give your answer in cm and to the nearest whole number. Do not put units in the answer box.
Find the cross sectional dimensions of the smallest square beam that can be loaded as shown in the figure if the allowable shearing stress is 1.0 MPa and the allowable bending stress is 8 MPa. 22 kN 18 kN m -2 m-2 m 3 m
Solve the problem with diagrams and figures in the solution.
Solution?
A timber beam AB of a span of 5 m, a width of 150 mm, and a height of 250 mm is to support three concentrated loads shown in the figure. Calculate the maximum shear and normal stresses for the selected timber beam for the given loading conditions. The selected grade of timber has the following material allowable; T₁=1 MPa and ₁=10 MPa. 15 KN 0.5 m 10 kN 1.0 m 5.0 m 15 KN 1.0 m 0.5 m B 150 mm 250 mm Cross Section
STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12)
Estimate the loads applied on the Beam 1, including the load transferred from Slabs 1 and 2 (self-weight of slabs), the self-weight of Beam 1 and the water tank load. Note that the water tank load may be idealised as a point load. Please also note that there are also other types of loads, which should be considered for practical design, but for simplicity they are not considered here.
a) Dimensioning of concrete beam i borderline conditionA free-standing beam in concrete with 4Φ20 K500-T is preliminary dimensioned according to the figure below.Estimate the load q that it can handle according to dimensioning for bending moments.Figure 1. Britt laid beam with rectangular cross-section. b=450mm d=550mm concrete=C35 steel=K500-T Draw moment and transverse force diagrams in scaled figures. Show the calculations in all steps andindicate where formulas and table values are taken from.
a) Dimensioning of concrete beam i borderline conditionA free-standing beam in concrete with 4Φ20 K500-T is preliminary dimensioned according to the figure below.Estimate the load q that it can handle according to dimensioning for bending moments.Figure 1. Britt laid beam with rectangular cross-section. b=450mm d=550mm concrete=C35 steel=K500-T Draw moment and transverse force diagrams in scaled figures. Show the calculations in all steps andexplain formulas.
A simply supported timber beam 20 cm wide and 40 cm deep carries a point load W at the middle point. The permissible stresses in flexure (bending) and shear is 100 N/cm2 and 150 N/cm2 respectively. Calculate the span length below which the shear stress will govern the safe load and above which the bending stress will govern the safe load.