PROBLEM 1: A reinforced concrete beam has a simple span of 8m. I t carries a concentrated factored load, Pu, at midspan. The beam is reinforced with 3D25mm. It has a width of 300mm and an offective depth of 450mm. Neglecting the weight of the beam, and using the exact/detailed calculation for Vc, a. What is the ultimate shear capacity of concrete at a section 2m from the support? b. What should be the shear capacity of web reinforcement at the section 2m from the support? c. What is the maximum spacing of web reinforcement allowed by the code at the section 2m from the support if the diameter of stirrups is 12mm? d. What is the required spacing of web reinforcement at the section 2m from the support if the diameter of stirrups is 12mm?

PROBLEM 1: A reinforced concrete beam has a simple span of 8m. I t carries a concentrated factored load, Pu, at midspan. The beam is reinforced with 3D25mm. It has a width of 300mm and an offective depth of 450mm. Neglecting the weight of the beam, and using the exact/detailed calculation for Vc, a. What is the ultimate shear capacity of concrete at a section 2m from the support? b. What should be the shear capacity of web reinforcement at the section 2m from the support? c. What is the maximum spacing of web reinforcement allowed by the code at the section 2m from the support if the diameter of stirrups is 12mm? d. What is the required spacing of web reinforcement at the section 2m from the support if the diameter of stirrups is 12mm?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The maximum load of 200 KN was applied on a cylindrical specimen of concrete. Find the split tensile strength in MPa. Take depth as 150 mm and length as 300 mm.
A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressive load the composite strut can support if the stress in the concrete is not exceed 2N/mm2. By how much should the strut shorten under this load. For cat iron EA= 100GN/m? and for concrete Eb = 10GN/m?. %3D
I need to solve this in concrete
1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21 MPa, fy = 414 MPa. The beam is reinforced for tension only. Determine the design strength under the following conditions. a.) When the beam is reinforced with three 25 mm diameter bars. b.) When the beam is reinforced with four 25 mm diameter bars. c.) When the beam is reinforced with seven 25 mm diameter bars.
T beams
Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. The concrete cover to bar centroid is 80 mm and at the bottom is 70 mm. use concrete strength f'= 21 MPa and steel yield strength fy=415 MPa for all bars. 1. Determine the tensile steel ratio when the beam is in positive bending. a. 0.01567 b. 0.01283 c. 0.01169 d. 0.01923 2. Determine the nominal moment capacity in kN-m of the beam in positive bending. a. 188.30 b.167.70 c.218.96 d.193.68 3. Determine the tensile steel ratio when the beam is in negative bending. a. 0.00406 b. 0.00475 c.0.00383 d. 0.00508 please provide a complete solution so I can understand. Very much appreciated to solve it early !!
CAN SOMEONE HELP ME SOLVE THIS REINFORCED/PRESTRESSED CONCRETE PROBLEM. USE NSCP 2015 A concrete beam has a width of 304.8 mm and an effective depth of 495.3 mm. It is reinforced with 14.194 cm2 steel bars with fc′ = 17,237.5 kPa (n = 10). Determine the flexural stresses caused by a bending moment of 84.1 kN·m
A 6m long simply supported reinforced concrete beam has a width of 350mm and an overal1 depth of 470mm. The beans is reinforced with 2-28mm compression bars and 4-28mm tension bars, each located 70mm from the extreme fibers. Concrete strength f'c = 20. 7 MPa, and steel yield strength fy=415 MPa. Determine the ff: 1) Depth of compression block assuming both tension and compression steel yields. 2) what is the ultimate moment capacity of the beam in KN.m. 3) Determine the additional concentrated live load that can be applied at midspan if the dead load including the weight of the beam is 20KN/m. Use Mu=1.2Mdl+1.6M11 (Based of NSCP 2015) Show complete solution and neat handwriting. Use NSCP 2015.
SITUATION IIl: A reinforced concrete beam with a cross-section of 250mm x 460mm (60 mm steel cover). Use the following properties to calculate what is required: f'c = 20.7 MPa fy = 344.7 MPa %3D As = 3-36mm A's = 2-25mm 8) Draw the stress diagram of the beam section 9) Calculate for the depth of the compression block. 10) Calculate for the compressive strength of the concrete (in KN). 11) Calculate for the nominal moment capacity of the beam.
I need to solve this question in concrete
Give me right solution according to the question.. where Y = 146 X1 = 102.2 X3= 146 X= 551 X2= 363.66