flat plate floor having a grid of 4x5m, with exterior beams and without interior beams,with (350x350)mm columns, the slab is to carry a total dead load (including slab weight) of3.5kN/m², and live load SkN/m², fe' - 25MPa, fy = 420MPa,. bw-250mm, h-500mm, ts170mm. (Note: don't need to check the D.D.M limitations)a) Find the column strip bending moment in the short direction of Panels 1 and 2.b) Check shear for the interior column 1 for one and two way actions.4.04.00.54.0**P1Col.1-P2R0.35.05.05.0

Answered: Image /qna-images/answer/ac3b221d-fe2f-4025-a1c0-d3a87aa9707c.jpg

Answered: a) Find the column strip bending moment…

a) Find the column strip bending moment in the short direction of Panels 1 and 2. b) Check shear for the interior column 1 for one and two way actions.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw moment and shear diagrams for members CD and BC. 8 k/ft A E El = constant 10 ft 10 ft |- ㅜ 10 ft 15 ft
This a mechanics of material question please show all steps so your approach is easily followed. Please show Free body diagram, what is given, and what the problem is asking for. Thank you
Beam ABCD carries a varying load on segment AB as shown below and a counter clockwise couple at point C. Find the shear BC (VBC) of the beam. 25kN/m with M=30kNm 2m t $1.5m VB A 1.5m D
The box beam has an allowable bending stress of o= 10 MPa and an allowable shear stress of 7=775 kPa. Determine the maximum intensity w of the distributed loading that it can safely support. Also, determine the maximum safe nail spacing for each third of the length of the beam. Each nail can resist a shear force of 200 N. 30 mm 250 mm 30 mm 150 mm 30 mm 6m
Calculate for the following member forces of the frame shown below using Portal Method. a. Shear at column FE, VFE in kN b. Shear at column ED, VED in kN c. Shear at beam FC, VFC in kN d. Moment at A, MA in kN-m e. Moment at girder KH, MKH in kN-m
Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member BC and the diameter of the pins at A and B if the allowable normal stress is allow 3 ksi and the allowable shear stress is allow = 4 ksi. 1500 lb -2 ft -4 ft- 1500 lb B 60°
From the observed data in a pycnometer test indicated in the table above, determine the specific gravityof the soil solids.
For the load group and influence line shown, P₁ = 32 kips, P2 = 32 kips, P3 = 8 kips, a = 14', and b = 14'. The influence line is for V40- = shear just left of 40! Determine V40- in kips to two decimal places when the force P₁ is at 16'. Use the correct sign. -1 X 19.2 16 0.5 15 20 30 -1 ५० P₂ P2 P₂ a b P3
Q9( e ): If the pins D and C are subjected to single shear while pin at A is a double shear. The diameter of pin D and C are 1.5 in while the diameter 5 ft of pin A is 1 in. Determine the shear stress at pins A,D and C. Also find the stress in the bar DC if its diameter is 0.5 in. JE -3 ft3 ft-3 ft- 600 Ib
For the load group and influence line shown, P₁ = 8 kips, P₂ = 32 kips, P3 = 32 kips, a = 14', and b = 18'. The influence line is for V40 = shear just left of 40'. Determine V40- in kips to two decimal places when the force P₁ is at O'. Use the correct sign. -1 16 0.5 15 20 30 1 P₁ P₂ a b P3
The answers are given i just need the solution. Please make the solutions clear and readable. Thank you.