"Prob. 4.3-6. The solid shaft in Fig. P4.3-6 is made of brass that has an allowable shear stress allow= 120 MPa and a shear modulus of elasticity G = 39 GPa. The length of the shaft is L= 2 m, and over this length the allowable angle of twist is dow= 0.10 rad. If the shaft is to be subjected to a maximum torque of T = 25 kN m, what is the required diameter of the shaft? 0 P4.3-5 and P4.3-6 T

"Prob. 4.3-6. The solid shaft in Fig. P4.3-6 is made of brass that has an allowable shear stress allow= 120 MPa and a shear modulus of elasticity G = 39 GPa. The length of the shaft is L= 2 m, and over this length the allowable angle of twist is dow= 0.10 rad. If the shaft is to be subjected to a maximum torque of T = 25 kN m, what is the required diameter of the shaft? 0 P4.3-5 and P4.3-6 T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

0.13
2.0 in 3.0 in. The tubular torsional shaft shown above is made ofa stainless steel metal with the following properties: E = 28500 ksi • G= 11000 ksi • v = 0.37 If the pipe cross-section is subjected to an internal torque of T 50 kip-in, which of the following is closest to the minimum shear stress action on the cross-section? 3.92 ksi 1.57 ksi 7.84 ksi
Kindly show complete solution. Solve the reactions and draw the shear and bending moment diagrams for the beam shown using the method of Consistent Deformations.
1. THE MEMBERS OF THE STRUCTURE SHOWN BELOW WEIGH 2918 N/M, DETERMINE THE SMALLEST DIAMETER OF PIN THAT CAN BE USED AT A IF THE SHEARING STRESS IS LIMITED TO 34470 kfa. ASSUME SINGLE SHEAR. 1.20 m 1.80m 1,20 M 0.90 m
The bell crack mechanism shown in Figure is in equilibrium for an applied load of F1 = 15KN at A and F2 at C. The pin at B has a diameter of 12mm. The thickness of the bell crank is 8mm while the support bracket has a thickness of 6mm. The bell crank and the support bracket each have an ultimate bearing strength of 550 MPa. a %3D = 300 mm; b = 150 mm ; c = 100 mm; 0 = 65° %3D 30° (2) Bell crank B a Fi H-8 mm В Bracket 6 mm 6 mm Connection detail Determine the factor of safety in the support bracket with respect to the ultimate bearing strength.
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
0.15
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Steel type is W310 X 74. P1= 40kN P2= 30kN. Find principal stress and shear stress at point '' a '' and '' b''
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B 20-mm diameter 60-mm diameter 1. Determine the deformation at segment AB in millimeter if P = 58 kN and Q = 0.
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
Radius of the pin at C is 3mm. While at static equilibrium, we know that a force P of magnitude 500 N is applied to the pedal shown, calculate (a) The average shearing stress in the pin at C (b) the corresponding bearing stress in the pedal at C, (c) the corresponding bearing stress in each support bracket at C. 9 mm T 5 mm C A 75 mm 125 mm B 300 mm PI D