A feedback amplifier employing series-series feedback is shown in the figure below, where thefeedback network is contained inside the dashed box. For the open loop amplifier, R₂ = 5kn,Gm = 100mS, and R. = 1k. The other component values are R₁ = 2kN, RB = 1kN,Rs = 7kN. and R₁ = 6kn. Express your answers up to 3 decimal places.RsMRiVinMRAGm. VinRB3. What is the loaded open loop amplifier gain?ioutUs4. What is the closed loop gain of the amplifier, -?RomSi outmSRL

Answered: Image /qna-images/answer/adcce278-61d0-4b84-9740-53244bdb906f.jpg

A feedback amplifier employing series-series feedback is shown in the figure below, where the feedback network is contained inside the dashed box. For the open loop amplifier, R₂ = 5kn, Gm = 100mS, and R₂ = 1k. The other component values are R₁ = 2kN, RB = 1kN, Rs = 7kN. and R₁ = 6kn. Express your answers up to 3 decimal places. Rs M Ri Vin M RA Gm. Vin RB 3. What is the loaded open loop amplifier gain? iout Us 4. What is the closed loop gain of the amplifier, -? Ro mS i out mS RL

A feedback amplifier employing series-series feedback is shown in the figure below, where the feedback network is contained inside the dashed box. For the open loop amplifier, R₂ = 5kn, Gm = 100mS, and R₂ = 1k. The other component values are R₁ = 2kN, RB = 1kN, Rs = 7kN. and R₁ = 6kn. Express your answers up to 3 decimal places. Rs M Ri Vin M RA Gm. Vin RB 3. What is the loaded open loop amplifier gain? iout Us 4. What is the closed loop gain of the amplifier, -? Ro mS i out mS RL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1 Design an operational-amplifier circuit using two inverting configurations to produce the output vo = +201 + 0.5v2 – 0.2v3 – 1v4. Choose feedback resistor Rf = 220kN for each amplifier. %3D | -
Ques 2: What is the Voltage series feedback? Explain the effect of feedback on gain and input, outputimpedance
Plz solve both , i vll share positive feedback and vll upvote.... ASAP PLZZ
Assume that the R2/R1 ratio of a feedback amplifier with voltage supply of +/- 10 V is 3.4 and that a value of 8.5 V is applied to the inverting input of the op-amp. What is the output voltage value?
QI. A siniscidal voltage waveform with 5 V pk-pk and period of 10 as is applied to the input of the op-amp shown in the figure. The open loop gain is 200000 and the supply voltage is +12 . Draw the input and output waveforms showing the time relationship. Vee
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
Consider the ideal shunt-series feedback amplifier in Figure below. Assume that the source resistance le 4 is Rs = 00. (a) If I = 100 µA, I fh (b) Using the results of part (a), determine Rif and Rof, for Ri = 5 kN and R, = 4 kN. 99 µA, and I, = 5 mA, determine A, B, and G, including units. %3D
Design and draw a three-stage amplifier connected in series with gains of +15, –21, and –30 by using OPAMPS. Use a 420 kn feedback resistor for all stages. What output voltage results for an input of V, = 2 mV?
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
B- Design a floating current-to-voltage converter that will convert a 4-to20 mA current signal into 0-to 10 V ground-referenced voltage signal. Let the Gain is 5 and feedback resistor (R) is 20 KN.
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?