A fabricated assembly made from three different sizes of standard steel tubing is shown below. The larger tube on the left carries 0.072 m3/s of water. The tee branches into two smaller sections. If the velocity in the 50-mm tube is 12.0 m/s, what is the velocity in the 100-mm tube? Ans. 7.88 m/s

Q: A garden lawn spreader is powered by the wheels. The wheels are connected to the spreader by a set…

A: The velocity of the wheel is .The radius of the wheel is .The diameter of the gear 1 is .The…

Q: 4. A pipe has an initial radius of 30cm, which then changes to a radius of 10cm. The velocity of the…

A: Given data: r1=30 cmr2=10 mh=0.5 mv1=2 m/s Need to determine the pressure difference between the two…

Q: Find the specific speed of the pump, if the discharge through the pump is 160 liters/sec, speed is…

A: Given values are, discharge Q= 160litres/sec=160×10-3m3s speed N=1000rpm ,head H=27.5 m The specific…

Q: Q2) ) A piping system consists of three pipes arranged in series the lengths of the pipes are…

A:

Q: Q3) The unsteady low of water through the reducer shown in Fig.2 is such that the velocity at A is…

A:

Q: where do v sub 1 came from? which is 0.95m/s

A:

Q: 1. A pipe 100 mm bore diameter carries oil of density 900 kg/m3 at a rate of 4 kg/s. The pipe…

A:

Q: Flow in a turbine flows through the turbine shown in the Figure below. nt A, the velocity in pipe is…

A: GivenVA=11.14m/sPA=1.2bar=120kPaP=0.5bar=50kPaZA=1mhL=0.3mdA=0.2mdB=0.4m

Q: The axial flow pump produces a discharge of 0.095 m³/s. ( Figure 1) The impeller is rotating at w =…

A: According to the given data Discharge, Q=0.095 m3/s ω=80 rad/s Mean radius, r=75 mm We need to find…

Q: . Water flows through a constricted pipe at a uniform rate. At one point, the diameter of the pipe…

A:

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A: Given:The diagram of the problem is given below;The volume flow rate through the larger tube, The…

Q: The three-tanks system in figure are interconnected as shown. Compute the flowrate in each pipe,…

A: To find discharge in all pipes

Q: A uniformly tapering pipe has 120mm and 80mm diameters at its ends. If the velocity of water at the…

A:

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 2 D2=20 cm

A:

Q: 6.31 In a pipe 0.3 m in diameter, 0.3 m³/s of water are pumped up a hill. On the hilltop (elevation…

A:

Q: Calculate the discharge through the 140-mm diameter orifice shown. Assume C = 0.62.

A: Need to find the discharge through orifice.

Q: 0.99 m 2.8 m 5 cm - diameter Group (C) Determine the discharge, the velocity of flow and pressure at…

A:

Q: A 45° reducing bend in a horizontal plane, 0.59 m diameter upstream and 0.23 m diameter downstream…

A: The given values are -  Q =0.46 m3/sd1=0.59 m , d2=0.23 mP1 =1.46 bar =146 kPa Assuming that the…

Q: Eight cubic feet of water flow per second downward through this pipe line. When the upper pressure…

A:

Q: A pipe that is 200 mm in diameter (point 1) diverges into segments 150 mm (point 2) and 90 mm (point…

A:

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A:

Q: What is the velocity of the pipe center (m/s)? Given that h3=68.9 cm h2 =7 cm h =3 cm Water .

A: given data: difference in head at pitot tube be h; according the question h = h3 h = 0.689m taking,…

Q: 8.111 The flowrate between Tank A and Tank B shown is to be increased by 30% (i.e., from Q to 1.30Q)…

A: For solution refer below images.

Q: A fluid flows at 650 (ft^3)/min through the space between two concentric pipes. The inner pipe has…

A: Given: Q = 650 ft3 /min d = 1.5 in.  D = 4 in.    To find: Average velocity, uavg = ?

Q: An old pipe is to be replaced by a new one with the same diameter and length. If the friction factor…

A:

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 3 D2=20 cm P2=100 Kpa…

A:

Q: b) The figure below shows a plan view of a 90° bend and a reducer cast altogether in one anchor…

A:

Q: Water with a velocity of 7.06 m/s flows through a 73 mm diameter pipe. Solve for the mass flow rate…

A:

Q: A pump has a brake horsepower of 39 hp with an efficiency of 81%. Neglecting frictional losses,…

A:

Q: A2 v1=0.2m/s V2=6m/s v1=0.2m/s V2=8m/s v1=0.2m/s V2=0.6m/s v1=6m/s A hydraulic pump delivers Q-10…

A:

Q: 8.61 cally through a 200-fi-long, 1.0-in.-diameter drawn tubing at a rate of 0.060 ft'/s if the…

A: Given that, Length of pipe, L=200 ftL=60.96 m,Diameter of pipe, d=1 in,Volume flow rate of water,…

Q: Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe…

A: Given:Bulk velocity of water through the pipe, V=0.4 m/sInternal diameter of the pipe, d=250…

Q: QUESTION 2 A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant…

A: by problem,QB=QCQA=QB+QCQB=QC=QA/2f=0.0075DA=DB=50mmDC=?For A & B reservoir,ZA-ZB=fCADA X VA22g…

Q: The three tanks shown in the figure below are connected by new cast iron pipes (ɛ = 0.26 mm). The…

A: Given: To Determine: Flow rate in pipe 2 and 3 and required  pump power.

Q: Compute the ideal flow rate through the pipe system shown in Fig. 8-37. 1.2 m 200 mm -100 mm 0.6m…

A:

Q: 9. What is the diameter, in millimeter, of an orifice in a tank with a cross-section of 1.5 m? if…

A: A=1.5m2 c=0.63

Q: What is the velocity of the pipe center (m/s)? Given that h3%-88.3 cm h3 h2 =7 cm h =3 cm] Water

A: hps=88.3+7hps=95.3 cm or 0.953 mhp=7 cm or 0.07 m apply bernoulli's equation between 1 and…

Q: Water flows at 10 m/s through a pipe. The pipe's radius then becomes 40% of its original size. What…

A: According to the  given data First pipe radius  =R with velocity v=10m/s Second piperadius=r=0.40R…

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A: Given: The flow rate, Q = 400 gal/min The pipe type = schedule 40

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: As per bartleby guidelines we are allowed to solve 1st 3 subparts of question. Please post remaining…

Q: A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.