The water is flowing through a pipe having diameters 200 mm and 100 mm at sections 1 and 2 respectively. The rate of flow through the pipe is 35 liters/s. The section 1 is 6 m above datum and section 2 is 4 m above datum. If the pressure at section 1 is 400 kN/m2, find the intensity of pressure at section 2 in kPa. Choose the correct answer below. a. 12.2 b. 410.5 c. 13.7 d. 125.2

Q: Oil is flowing through the venture meter shown in the figure. The water velocity in the main pipe of…

A:

Q: Q2) ) A piping system consists of three pipes arranged in series the lengths of the pipes are…

A:

Q: 1) At the instant the valve is opened, the Venturi meter indicates a pressure difference of 735 kPa.…

A:

Q: 10. Water flows from a lake as shown below at a rate of 5.0 ft³/s. Is the device inside the building…

A:

Q: A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in…

A: Given, Q=2 L/min=2×10-360 m3/s=3.333×10-5 m3/s d1=50 mmd2=25 mm hl=kv22-v122g z1-z2=1.5 m

Q: A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point…

A:

Q: Determine the flow through a linear characteristic, valve when the valve position is 60%. The…

A: Given:- Valve position, x =60%=0.60 Maximum flow, Qmax=120 gpm To find:- Flow when the valve is at…

Q: 4 ft 2 ft Determine the rate of discharge and gage pressure at point A. А.

A: Given : The diameter of pipe is The free body diagram is,

Q: 2. a. Find the expression for dh dt dh b. Compute if D₁ = 1in, D₂ = 3 in, dt V₁ = 3ft/s, V₂ = 2ft/s,…

A:

Q: Q1/ A45' reducing bend is connected in apipe line, the diameters at the inlet and outlet of the bend…

A: Answer: The force exerted by water on the bend is 20891 N at 17.62° in clockwise direction from…

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A:

Q: Water with flow rate of 12 lps from ground level is delivered to upper levels using the 50-mm…

A: Given,  The water flow rate, Q = 12 L/s The diameter of pipe, d = 50 mm The angle between inlet and…

Q: A piping system has a Y-configuration for separating the flow as shown in Figure 4. The diameter of…

A: Given data:

Q: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure…

A: First we calculate the diameter at outlet and inlet  D1= 8 in(1/12 ft)=2/3 ft D2=6 in(1/12ft)=0.5 ft…

Q: 6) Determine the internal energy of water at 20 psi and 400 F

A:

Q: 4.Oil with specific gravity 0.750 is flowing through a 6-in pipe under a pressure of 15.0 psi. If…

A: The given information in the problem is shown in the following attached image:

Q: Eight cubic feet of water flow per second downward through this pipe line. When the upper pressure…

A:

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: Consider a series of pipes as shown in the figure below that carries a discharge of 100 of water.…

A:

Q: What is the velocity of the pipe center (m/s)? Given that h3=47.1 cm hy =7 cm h =3 cm Water

A: Solution:

Q: 3.- A swimming pool has a partial filtration system, the water whose temperature is 75 °F, is pumped…

A: The water temperature, T = 75 FThe discharge through the pump, Q1 = 30 GPMThe pressure inside the…

Q: 3. Determine the value of Q₁, Q₂, Q₁, d₁, Q4 and v₁ when water flows through the pipes which are…

A:

Q: n the Picture above OBE locm /Bc = 2Scm Ehe Vtelve of nŋ or rotation cl dao rem Convert this vawe to…

A:

Q: QUESTION 4 A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25…

A:

Q: 2-the discharge through the pipe shown in fig. below is 0.4m'sec and the pressure head for point A…

A:

Q: Two reservoirs are connected with a pipeline see figure 2. The first section of the pipeline from…

A:

Q: 9. What is the diameter, in millimeter, of an orifice in a tank with a cross-section of 1.5 m? if…

A: A=1.5m2 c=0.63

Q: 1-Comment on the differences in reading measurements and whether these differences could be from…

A: Answer:1)i)The accuracy of measurements of readings in flows depends on the fluid properties.ii)The…

Q: Q1: If flow rate in pipe shown is (0.5m'/s) find the (H). H. water D=300 mm

A: Given data Volume flow rate = Q = 0.5 m3/sDiameter of pipe = 300 mm = 0.3 m

Q: The mean effective pressure of an engine running at 450 rpm is 550 kPa. What is the indicated power…

A:

Q: 15 m. Determine the rate of flow of water through the pipes pipe of length 1700 m and f= .005, which…

A:

Q: flow rate of water in the pipe which is con ed to tank B is the flow rate in the other two pipes and…

A:

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Q: 1. Two round pipes have water flowing through them. Pipe B is half of the diameter of pipe A. If the…

A:

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A:

Q: total energy

A:

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A:

Q: A pipe with a radius of 9 mm is attached to a nozzle. If the velocity of flow in the pipe is 2 m/s,…

A:

Q: Use f=0.012 for all pipes and initially assume equal flow in pipes AB and AE. Determine the…

A:

Q: Q1: If flow rate in pipe shown is (0.5m/s) find the (H). H. water D=300 mm

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.