A F F W2 d A Section A-A The following figure shows the free-body diagram of a connecting-link portion having stress concentration at three sections. The dimensions are r = 0:25 in, d = 0:75 in, h = 0:50 in, w1 = 3:75 in, and w2 = 2:5 in. The forces F fluctuate between a tension of 4 kip and a compression of 16 kip. Neglect column action and find the least factor of safety if the material is cold-drawn AISI 1018 steel.

A F F W2 d A Section A-A The following figure shows the free-body diagram of a connecting-link portion having stress concentration at three sections. The dimensions are r = 0:25 in, d = 0:75 in, h = 0:50 in, w1 = 3:75 in, and w2 = 2:5 in. The forces F fluctuate between a tension of 4 kip and a compression of 16 kip. Neglect column action and find the least factor of safety if the material is cold-drawn AISI 1018 steel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

k 2 13 ki Rigid bar k3 3 for the system shown in the figure, which of the following statements are correct. * u2 = P %3D !! u = u2 = U3 = U4 = 0
In the figure, copper AB copper with a diameter of 24 mm and BC steel bars with a diameter of 20 mm are rigidly connected to each other at point B. A force of 6 kN was applied to the rod at the B point and 12 kN at the C point. Since the modulus of elasticity of copper is 100 GPa and the modulus of elasticity of steel is 200 GPa, find the displacement of the C point.
Define the terms load , stress and strain. Discuss the various types of stresses and strain p 4:19 /
A bridge truss extends x = 206 m across a river (shown in the figure below) where 8 = 39º. The structure is free to slide horizontally to permit thermal expansion. The structural components are connected by pin joints, and the masses of the bars are small compared with the mass of a 1340 kg car at the center. Calculate the force of tension or compression in each structural component (in N). B TAB = TAC = TBC = TBD TDE TDC= TEC = 11 N ---Select--- N ---Select--- N ---Select--- N ---Select--- N ---Select--- N ---Select--- N ---Select--- C X D E
Gkuestrons T ØD VP The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads. You are given the column diameter D = 68 mm, the groove radius r = 6 mm, the distance L= 200 mm, the bending load P=5 kN, and the torque T = 600 N.m. The material data are Young's modulus E = 122 GPa Shear Modulus G = 55 GPa Poisson's ratio v= 0.1 and Yield strength oy = 380 MPa. a) Write a numbered list of the calculation steps required to obtain the factor of safety in yielding based on the maximum distortion energy (Von Mises) criterion.
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
Problem 2 In the system below, two rigid bodies (Nodes 1 and 3) are connected by four springs to walls on either side, as shown in the figure. Nodes 2 and 4 are fixed (wall). An external force of 10 N is applied to body 1 (Node 1). The spring constants are given as kı=10 N/m, k2=20 N/m, k3=30 N/m, and k4=40 N/m. Assume that the bodies can only undergo translation in x-direction (1 DOF). Using the direct method: a) Find the displacements of the two rigid bodies (Nodes 1 and 3). Hint: units! b) Find the reaction force at the left wall (Node 4). Hint: units! E1 E2 3) F1 www 4 Е4 X
Consider the two bars of identical material with their elastic modulus E as shown in Figure below. Both bars have the same circular cross-section with diameter of d. The length of the longer bar is 2L and the length of the shorter bar is L. The angle between the bars is B. The system is subjected to a vertical force acting at point Pas shown in the figure with a magnitude of F. Calculate horizontal and vertical components of the displacement of point P. Use engineering notation (ENG display mode on scientific calculators) with 3 significant figures after the decimal point. E (psi) 1.50E+06 d (in) 1.25 L (in) 12 Beta (degrees) 30 F (Ibf) 110 F P L 2L
Q3
An artist designs a mobile of light horizontal rods connected by vertical strings and supporting various shaped weights (see figure below). Find the magnitudes w₂, W3, and w4 if W1 2.56 units of weight. The numerical values given in the figure all have units of length. W2 = 7.68 W3 = 9.75 W4 = = 10.24 X X units of weight units of weight units of weight 30.0 10.0 W2 30.0 30.0 W3 20.0 10.0 WA
The figure illustrates a torsion-bar spring OA having a diameter d = 12 mm. The actuating cantilever AB also has d = 12 mm. Both parts are of carbon steel. Use Castigliano’s theorem and find the spring rake k corresponding to a force F acting at B.
Parvinbhai