a drone begins flying towards a target located 200 m away from a point of constant altitude. The speed of the drone is 5 m /s and is always towards the target throughout the movement. The wind at a speed of 3 m/ s blows perpendicular to the starting point and the target direction. Assuming that the drone is drifting with this wind speed, find the graph of the motion path of the drone.

a drone begins flying towards a target located 200 m away from a point of constant altitude. The speed of the drone is 5 m /s and is always towards the target throughout the movement. The wind at a speed of 3 m/ s blows perpendicular to the starting point and the target direction. Assuming that the drone is drifting with this wind speed, find the graph of the motion path of the drone.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

04: Find the fraction of the body centered cubie umit eel volume filled with hard spheres as shown in figure below if the total volume of cell (cubic) is 343 cu.
Air flowing at 604000 kilograms per second at a speed of 57 kilometres per hour. Assume the power coefficient of the wind turbine is the maximum possible as given by the Lanchester-Betz limit and gear, generator and electric efficiencies are 92%, 93% and 91% respectively. Determine the following: i. Wind power. ii. Mechanical power that could be achieved by the wind turbine rotor. iii. Electrical power output of the wind turbine.
Write down the rules for drawing root locus and explain them in detail.(Angle condition, departure and joint points, virtual axis cut points, arrival and turn angles.)
A shunt generator us connected to a load that draws 8.8 kW, Ra= 0.04 ohms and Rsh=. 48 ohms. If the power developed in the armature is 106.3% of the power delivered to the load, determine the terminal voltage of the generator. A 15 kW, 230 V shunt generator was run light as a motor to determine its stray power losses at rated load . The applied voltage across the armature computed for test was 254 V and the armature current drawn is 2 A. The armature and shunt field resistances are 0.25 and 100. ohms, respectively. Calculate the generator efficiency at half load. Assume stray power losses to be constant. A shunt generator supplies 100 A at 200 V. The armature and shunt resistances are 0.025 ohms and 100. ohms respectively. If the copper losses are equal to the iron losses at this load, find the brake horsepower of the engine driving the generator.
Which of the following statements regarding the aerodynamic efficiency and tip speed ratio of a wind turbine are correct? Select one or more: a. The optimal tip speed ratio for a Darrieus rotor is about 5. Ob. The optimal tip speed ratio for a 1-blade rotor is 15. c. The maximum efficiency (aerodynamic) of the 2-blade rotor is about 46%.
A d.c. A shunt generator delivers a load current of 80 A at 400 V. Its armature and field resistances are 0.20 and 100 respectively. Stray losses are 1500 watts. So find (1) mechanical (2) electrical and (3) commercial efficiency.
control system , plz fast fast
The poles of a system are:P1=1, P2=(2+7), P3=(3+7), P4=(4+7), and P5=(5+7)(i) Draw the system in complex z-plane(ii) Determine the possible ROCs(iii) Comments on the causality and stability for each ROC
5. Calculate the force exerted by each conductor, 9 in. long, on the armature of a DC motor, when it carries a current of 100 amp and lies in a field density of which is 55,000 lines per square inch.
sfer function of a control system. The poles are located as shown. The - Find the location of the intersection point of the asymptotes with the
Asiacell 会.ll .all Asiacell E Expert Q&A 6/33 Determine the distance s to which the 90-kg painter can climb without causing the 4-m ladder to slip at its lower end A. The top of the 15-kg ladder has a small roller, and at the ground the coefficient of static friction is 0.25. The mass center of the painter is directly above her feet. B 4 m A 1.5 m
Kindly answer both parts