A drawing operation is performed on 3.0 mm stock. The part is a cylindrical cup with height H = 50 mm and inside diameter Dp = 70 mm. Find the required starting blank diameter Db. Do not find the blank diameter. My question is why is the formula for the volume of cup = pi*Dp*h*t + pi*Dp2*t / 4. Are u able to illustrate it in the picture as i had trouble visualizing it A picture of the cylindrical cup is given.

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Hello, I don't understand how to solve 5-19 in the photo below. Because I can't find the correct…

A:

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: Use the graphical method to break F into components parallel to bars AB and BC. If the component…

A: According to the given data  FAB =7kN a = 300mm b = 75mm c = 100mm  we need to find Force in the…

Q: the figure shown, I=170mm, b=70mm and wAB=1100rpm (clockwise) olve for (a) the velocity(m/s) of…

A:

Q: Conversion of units: A pyramid has a height of 500 ft, and its base covers an area of 15.0 acres…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: ## Moment of Inertia Calculations (by hand)**Given:*** a = 22 ft* y = x^2 (for part a)* y = x (for…

Q: E 12.5 m C А 8 m 5 m

A:

Q: (1) A rod of length L has a small square cross section b²; the density of the material is p. Just by…

A:

Q: In (Eigure 1). F-700 N and @-20 Figure 30 FA-700 N 1 of 1 Determine the magnitude of the resultant…

A: If F= 700 N and thita= 20°Determine the magnitude of the resultant force.Determine the direction of…

Q: Help!!! Answer it correctly!!! Make sure you solve work on hand!!! Answer correctly Please!!!!!!!

A: Thank you,Please rate my response.

Q: Specify where the line of action of the resultant force intersects a horizontal line along member…

A: We have given the following problem

Q: A steel collar has an inside diameter of 1-1/8 in., an outside diameter of 3-3/4 in., and a length…

A: Given: internal diameter Di = 1-1/8 = 9/8 inches outer diameter Do = 3-3/4 = 15/4 inches length =…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.