The cross section of a wooden beam is shown. a. Calculate the I b. Calculate the force in nails in A(horizontal) and B(vertical) provided the nails are spaced at 60mm from each other at A and 25mm from each other at B locations. The vertical shearing force is 16kN. The beam is NOT drawn to scale.

Q: spring is k, and the spring is unstretched when = 90°. (a) Neglecting the weight of the rod, express…

A:

Q: 4. The control linkage of an airplane consists of a rigid member DBC and a flexible cable AB. A…

A:

Q: Question 29 Which of the following can change the hardness of a material? O Manufacturing process O…

A:

Q: PRObleM 3 For the showm position of the crank-shaft mechanism it is known that =9 s, 6=3 s, OA=R=0,1…

A:

Q: 5. A sample stream of dry gas is being withdrawn from a stack. The stack gases are at 200 °C and 730…

A: a) According to the given data, T= 200∘c and P= 730 mmHgVolume flow rate through filter = Vms+d=Vm y…

Q: 2. The slender bar AB shown is attached to small wheels, which roll on the horizontal and inclined…

A:

Q: 5. Determine the moment about point B of the applied loads on the cantilever truss shown. 500 lb 400…

A:

Q: 8. What is the estimated service life of a part made of aluminum that will be subjected to a…

A: Given data: σAl=20 ksiLifeS=1×106 cycles Need to determine the service life of aluminum and…

Q: 1- Calculate the pressure, temperature and velocity prior to the shock wave. 2- Determine if the…

A:

Q: 1) By volume, the major structural parts of a conventional airframe are predominantly: . Heavy solid…

A:

Q: For the given truss, compute the reaction forces and the bar forces N1, N2, N3.

A:

Q: F= 200 N %3D 30° 13 12 F2 = 260 N

A:

Q: Q2. A hydraulically actuated horizontal slider mechanism is illustrated in figure 2 where the motion…

A: Hydraulical horizontal slider mechanism is a mechanism which is actuated with the help of hydraulic…

Q: I need help solving problems 7, 8, and 9 pertaining to the print provided below.

A: (7). For the fractional dimensions, fractional tolerances must be applied.

Q: Problem 4.138 Replace the loading by an equivalent resultant force and couple moment acting at point…

A:

Q: In the figure shown below, the deflection of mercury is initially 208 mm. If the pressure at A is…

A: Given:Initial deflection of mercury, hHg=208 mm=0.208 mPressure at A is increased by =34 kPa=34*103…

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in…

A:

Q: 3. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

A:

Q: A pressure bulkhead is usually placed:

A: Answer = Option (B)

Q: Explain with neat sketch, the surface finishing process of “Sandblasting”. ( Minimum 1 and half…

A:

Q: diagram of member AC in Figure P4-2. 3' 3' A C 5' B 2 2

A:

Q: Two Standard spur gears have a diametral pitch of 10, a pressure angle of and a velocity ratio equal…

A:

Q: Can you answer the question on the picture and show your work neatly? thank you!

A: Let us divide the shaded area into 3 different sections as shown in the figure.

Q: Width = 4 m Radius of quarter circle = 5 m (A is the center) Height from water level to top of the…

A: Introduction In this problem, we will calculate the total force on the gate BC by first calculating…

Q: The image below depicts one section of a cam shaft which opens a valve to release the pressure in…

A:

Q: A 6.8kg cat is standing on a uniform beam that weighs 245.0 N. The beam is supported by a hinge…

A:

Q: The steel member shown below has a diameter of 69 mm, modulus of elasticity of E=200 GPa, and is…

A: Draw FBD

Q: Iron with a power rating of 1200 watts is left on the ironing board. The convective heat transfer…

A:

Q: Explain the concept of print spooling and its importance in the printing process.

A: Print spooling:Multiple users' access to printers is managed by a unique process called the spooler.…

Q: Explain step by step

A: Since you have asked multiple question we will solve first question for you if you want a specific…

Q: Explain the surface coating techniques such as plastic coating and painting, which is used in the…

A: To explain: The surface coating techniques such as plastic coating and painting, which is used in…

Q: 2. You are working for a glider manufacturer and have been asked to analyse the laminar boundary…

A: For the solution refer below images.

Q: Hello. Would it be possible to include detailed explanations in every step? Thank you.

A: Given: Two springs are opposite to each other and by the energy stored in spring A is transferred by…

Q: Beam ABD supports an 80 kg vertical mass connected at point D. The beam has a pin connection at the…

A:

Q: A plate in the shape of an isosceles right triangle with side length 4 meters is submerged in water…

A: Draw figure

Q: A figure shown below is to be blanking through a blanking die The material is 4mm thick stainless…

A:

Q: Go to page 1 vater vapor flowing at a rate of 300.0 mol/h is brought from 600.0 °C and 10 bar to…

A:

Q: Describe the principles and applications of 9D printing and its theoretical potential for advanced…

A: The concept of 9D printing is still in its early stages of development, but it has the potential to…

Q: Steam, initially at 700 lbf/in.², 550°F undergoes a polytropic process in a piston-cylinder assembly…

A:

Q: samples in materials

A: Answer 1 During the cutting and grinding of a sample for microstructure examination cooling is…

Q: Write clearly, Explain step-by-step.

A: Given data: Tooth of pinion, Np = 24 Rotating speed of pinion, ωp = 2500 rpm Tooth of spur gear, Ng…

Q: 6. The timber beam has a cross-sectional area of 2000 mm? and its modulus of elasticity is 12 GPa.…

A:

Q: A stranded steel cable with known cross section and modulus of elasticity supports a 950 lb gin…

A: Given data as per question weight of pole =950 lb A = 0.11 in2 V =30 fpm v=30×1260=6 inschange in…

Q: However, conduction heat transfer in radial direction through a cylinder (again under steady-state…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.