A drained triaxial compression test oh a saturated clay yielded the effective shear strength parameters as c' = 15 kPa and o 25°, Consolidated undrained tri axial test on ah identical sample of this clay at a cell pressure of 250 kPa developed a pore water pressure of 150 kPa at failure, The deviatoric stress at failure is

A drained triaxial compression test oh a saturated clay yielded the effective shear strength parameters as c' = 15 kPa and o 25°, Consolidated undrained tri axial test on ah identical sample of this clay at a cell pressure of 250 kPa developed a pore water pressure of 150 kPa at failure, The deviatoric stress at failure is

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter12: Shear Strength Of Soil

Section: Chapter Questions

Problem 12.13P

See similar textbooks

Similar questions

A consolidated undrained triaxial test was performed on a normally consolidated clay with a critical state friction angle of 230. After an initial isotropic consolidation at a cell pressure of 50 kPa, drainage was turned off, the cell pressure was increased to 85 kPa, and the sample was loaded to ultimate conditions. A pore pressure of 55 kPa was measured at ultimate state. What value of major principal total stress was measured at the ultimate state?
5. A consolidated, undrained triaxial test is being carried out on a normally consolidated clay where c - 0 and p'= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
A consolidated drained (CD) triaxial test was carried out on a normally consolidated clay. The specimen was consolidated under a cell pressure of 100 kPa and back pressure of 30 kPa. The axial deviatoric stress was increased very slowly to failure, so that there was no excess pore water pressure developed during the shearing. The specimen failed under a deviatoric stress of 130 kPa. The back pressure of 30 kPa was maintained throughout the test. (i) What is the friction angle in terms of effective stresses? (ii) What are the shear stress and normal stress acting on the failure plane? Solution fast please
Tri-Axial Tests
5. A consolidated, undrained triaxial test is being caried out on a normally consolidated clay where c = 0 and 41= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
specimen In a consolidated-drained triaxial test on aclay, the failed at the deviator Stress of 124 kN/m² effective stress friction angle is known tod 31° 31 What was the effective confining pressure at failure? If the be -
A consolidated drained (CD) triaxial test was carried out on a normally consolidated clay. The specimen was consolidated under a cell pressure of 100 kPa and back pressure of 30 kPa. The axial deviatoric stress was increased very slowly to failure, so that there was no excess pore water pressure developed during the shearing. The specimen failed under a deviatoric stress of 130 kPa. The back pressure of 30 kPa was maintained throughout the test. (1) What is the friction angle in terms of effective stresses? (ii) What are the shear stress and normal stress acting on the failure plane?
A soft clay in an unconfined compression test did not develop a failure plane but bulged during the test. The sample was 40 mm in diameter and 85 mm in length. The load carried at a strain of 15% was 70.4 N. Determine the shear strength.
solve the question provided in the image.
A CU triaxial compression test was performed on saturated sand at a cell pressure of 100 kPa. The ultimate deviator stress was 350 kPa and the pore pressure at the peak stress was 40 kPa (suction). Estimate the total and effective stress shear strength parameters.
, solve graphically only6. In a consolidated drained triaxial test on an OC clay with a cohesion value of 4 kPa, the total axial stress is17 kPa and the cell pressure is 1 kPaFind:a) The deviator stressb) The angle of the Mohr-Coulomb Envelopec) The angle of the Failure Planed) The values of σff and τffe) The value of τmax
A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure were determined to be 6100 psf and 4600 psf, respectively. a. Determine the angle of internal friction of the sand? b. Determine the angle of the failure plane? c. Determine the maximum principal stress? Please answer this asap. For upvote. Thank you very much