A diverging tube discharges water from reservoir at a depth of 10 m below the water surface. The diameter of the tube gradually increases from 150 mm at the throat to 225 mm at the outlet. Neglecting friction, determine the maximum possible rate of discharge through this tube. Water 10 m 150 mm Ø 225 mm 0 Activate Go to Sett

A diverging tube discharges water from reservoir at a depth of 10 m below the water surface. The diameter of the tube gradually increases from 150 mm at the throat to 225 mm at the outlet. Neglecting friction, determine the maximum possible rate of discharge through this tube. Water 10 m 150 mm Ø 225 mm 0 Activate Go to Sett

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Water flows steadily through the variable area pipe as shown. a) Determine the velocities in the large diameter pipe (12 cm) and the small diameter pipe (8 cm). b) Determine the discharge.
Water flowing through a contraction pipe with diameter of 20mm and 5 mmrespectively. If the velocity of water at the larger diameter is 0.5 m/s, determine the discharge in the pipe and the velocity at the smaller diameter. Based on your result,state the correlation between flowrate and area of pipe diameter.
! Fast Please
Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Determine the power required for the pump if the water flow rate is 60 kg/s. The fittings from pipe Di to pipe D2 and from pipe D2 to pipe D3 can be considered to be standard 90° elbows with velocity in pipe 2 for the friction loss. Data: h = 10 m, h2 = 3 m, L1 water viscosity = 1 cP = 103 kg/m-s, p= 1000 kg/m³. The pipe roughness is 0.05 mm. The pump efficiency is 75%. 50 m, L2 = 300 m, L3 = 2 m, D¡ = 0.2 m, D2= 0.5 m, D3 = 0.03 m, (1) D,, L, D2, L, Globe valve D3, L,
Q25
A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
2. draw fbd
Q.9) If the faucet (gate valve), at E is fully opened and the pump produces a pressure of 350 kPa at A, determine the flowrate out from the faucet at E. The valve at B remain closed. The pipe has an inner diameter of 30 mm, and f=0.01. Include the minor losses of the tee (K=0.4), the two elbows (K=0.9), and the gate valve (K=0.19). 0.65 m 3 m B 5 m
For the frictionless syphon shown, determine the discharge and the pressure heads at A and B. Consider a pipe diameter of 210 mm with the nozzle at the exit having 140 mm diameter. Consider a datum plane that is 0.16 meters above point A. 2.44 m 1.22 m 0.15 m
Determine the power required (Watts) to drive a reciprocating pump running at 1 rps and discharges oil (ρ = 850 kg/m3) at a rate of 375.3 gpm. The bore and stroke is 250 mm and 500 mm respectively. The total head developed is 27 m. Round off your answer to 2 decimal places
The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m° and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. 0.409 MPa 0.125 MPa a. The energy added in meters and the power delivered in kilowatts to the water by the pump. b. The mechanical efficiency of the pump. P 0.04meter Ø 0.1meter Ø
Kindly solve with full solution and explain. Thank you very much