A distributor cable in the form of a ring main ABCDEA, supplies loads of 20, 60, 30, and 40 A taken at the points B, C, D and E respectively, the feeding point being at A. The resistances of the sections are AB=0.1 S2, BC= 0.152, CD=0.12, DE = 0.05 2 and EA = 0.1 2. The points E and C are connected by a cable having a resistance of 0.3 2. Calculate the current in each section of the network.

A distributor cable in the form of a ring main ABCDEA, supplies loads of 20, 60, 30, and 40 A taken at the points B, C, D and E respectively, the feeding point being at A. The resistances of the sections are AB=0.1 S2, BC= 0.152, CD=0.12, DE = 0.05 2 and EA = 0.1 2. The points E and C are connected by a cable having a resistance of 0.3 2. Calculate the current in each section of the network.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

300 m ring distributor has loads as shown in Figure below, where distances are in meters. The resistance of each conductor is 0.2 2 per 1000 meters and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. 50 A 70 D 90 240 V Y A C 60 B = 233-2 V 100 A
Determine the approximate value of VDs of Figure 55. VDD 21V 910kn 2.2ka Q1 V. Ioss= 10mA V. =- 3.5V 110KQ 1ka Figure 55 O 12.97 V O 11.12 V 9.32 V O 13.51 V
Identify the loads which does not require a neutral. B 415V 415 V A 240ν C 240 V 240 V DI 240 V E F 415 V a. Load A & F b. Load A & B O c. Load E & F d. Load C & D
For the circuit shown below calculate VS in V when IDSS=12mA VP=-6V and B=120
A. Determine Vcc for the network shown in Figure (2), if Av=-290 and r, = 80KN. Vee-? RI 82KO Rc 3.3KO Ce Figure (2) B-100 R 11.2KA Re I KO3
Electrical Engineering Al (A2 A3 V1 Al A2 N m B1 B2 C1 w Ps 2 A To 240 V supply Supply Neutral NS C2 A4 LY I Is there a circulating current (A5) in the delta connected winding? Is there a significant current trough the short circuits (A6 & A7)? (iv) Does the short circuit on the secondary side make any difference to primary side? bl 62 a B A6 b A7 A5
Thanks
Compute the parameters R1 and Li from Bridge Circuit given in Figure 1. Construct the phasor diagram of the given circuit. C3 Li R3 RI C4 ww a R2 R4 E Figure 1: Bridge Circuit ww ww
Solve the circuit in the figure with the triangle-star method, find the current drawn from the 20V source and mark the correct answer for this current.
Under short circuit test, the short circuit voltage of transformer is O a. Equal to the rated voltage ОБ. O b. (3-5) % V rated O c. Maximum O d. Zero
181% O uo 9:02 Asiacell I. docs.google.com a A charge of 15C flow in a conductor in .5 * :2min, then the current produced is 125A O 0.125A 12.5A 1.25A In figure below, The total voltage of the .3 sources connected in series is HHH- 6 V 6 V 8 V +20v +4v -20v -4v + -> 72