Al A2 V1 Al A2 A B1 To 240 V supply B2 C1 Supply Neutral NS N C₂3 A4 A5 (ii) Is there a circulating current (A5) in the delta connected winding? Is there a significant current trough the short circuits (A6 & A7)? (iii) (iv) Does the short circuit on the secondary side make any difference to primary side? A3 m ww bl b2 a B A6 b A7

Al A2 V1 Al A2 A B1 To 240 V supply B2 C1 Supply Neutral NS N C₂3 A4 A5 (ii) Is there a circulating current (A5) in the delta connected winding? Is there a significant current trough the short circuits (A6 & A7)? (iii) (iv) Does the short circuit on the secondary side make any difference to primary side? A3 m ww bl b2 a B A6 b A7

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 2300V to 230V step down transformer is rated at 750 KVA and 60 Hz. Its winding have the following resistances and inductances: Re' =0.093 ohm Re" = 0.00093 ohm Xe' =0.280 ohm Xe" =0.0028 ohm The transformer is operating on rated load.
a)The voltage per winding of 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 50 0.0050 0.0025 60 b) The voltage per winding of 220V/12V, 50 Hz single phase core transformer is 2V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 60 0.0050 0.0025 50
QUESTION 25 Thickness of a transformer core lamination is in the order of O 2.0 mm O 1.5 mm O 0.5 mm O 2.5 mm O 1.0 mm QUESTION 26 In an autotransformer the resistance between its primary and secondary is O infinite O 500 Ohm O 1500 Ohm O low o unpredictable QUESTION 27 The main purpose of using an iron in a transformer is to: Oe decrease Pc Ob increase flux Oc decrease Pcu oa decrease m oeb&d
14. The maximum flux of a 50H2 transformer is 0.001Wb. If the primary is wound Vwith 1080 turns, find the applied primary voltage and then calculate the number of turns required for a 15V secondary. Ans: N2=67
QUESTION 5 A real transformer is connected to a 120V RMS supply voltage on the primary and a 2.5knL40* load on the secondary. Np = 500, Ns = 1500, Rp = 100, Rs = 250, Xp = 40, and Xs = 200. Calculate the magnitude of the voltage across the load. O 463V RMS O 108V RMS O 285V RMS O 343V RMS
I need help on questions 4-6. ALSO dpes Vp=600V and Vs=120V? Or is it Vp=720V and Vs=600V?
A transformer has "N1" primary turns, primary winding is connected with 'V1' Volts. if N2 = N1/2, what is the secondary voltage? O a. V2 = V1/2 O b. V2=2V1 c. V2=0 O d. V2=V1
For a CT, if primary current is 750A, and secondary current is 5A, then appproximated nurmber of primary winding turns will be O a. 5' O b.'1' OC.100' O d. '10' Meeting in "Gem
imary winding is connected o be applied at normal freq rough it when the secondary conner loss
To find: The loop currents using elimination & substitution methods
6. Identify the electronic symbol pointed by the line in the given schematic diagram F A TIP2066 with Heat Sink MA 01 Ohm E Sw TIP2055 wih Heat Sink B 10 Amp 50 PN Bridge Rectiter 0.1 Ohm SW LMTar2 we Heat Sink FUSE A FUSE 10A 230 Voit AC 12V Out o Gnd in 0.1 Ohm Sw 470uF 230112V 10A Transformer 47000UF Sov Output 10 uf 12V10A D A В C D F M CnolIL Choclk
32