(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determ maximum shear force and maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter yo shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo A В L. Answer: Vmax = kN Mmax = kN-m

(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determ maximum shear force and maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter yo shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo A В L. Answer: Vmax = kN Mmax = kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=4.50 m, b=5.00 m, c= 2.75 m, P = 33kN and M = 195kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. 1.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) (in kN) 2.Determine the shear force acting at each of the following locations: (in kN)(a) x = 4.50- (i.e., just to the left of point B)(b) x = 4.50+ (i.e., just to the right of point B)(c) x = 9.50- (i.e., just to the left of point C)(d) x = 9.50+ (i.e., just to the right of point C)Note that x = 0 at support A. 3. Determine the bending-moment…
Pls answer Express your intermediate answers with at least FOUR decimal places and simplify your FINAL answers up to TWO DECIMAL PLACES. BOX your FINAL ANSWERS. Complete solution with figure. Write legibly.
red is the correct answer
Note:Hand written solution not allowed.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.250 m, b=6.50 m, PA = 60kN, and PC = 70kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
X=450N, Y=900N
Answer the following and write on a clean paper written then box your final answer.
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
For the beam shown,(1) derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.)(2) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Specify the values for key points on the diagrams.Let a=10.1 ft, b=7.3 ft, wa=3.7 kips/ft, and wb=10.5 kips/ft. Derive the equations and construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Part 1 Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax=0, it has been omitted from the free-body diagram.)
Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1. What is the shear at E? 2. What is the shear and moment at point C? 3. What is the shear and moment at point A? please provide a solution, thank u so much.Given: Shear and moment at left of C Vc= -4.5 kn Mc= -4.5 kn-m Shear and moment at right of C Vc= 37.5 knMc= -94.5 kn-m
problem 9
The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w= 53 kN/m over 1.5 m from the left-hand end and moment loading M = 53 kNm at 1.5 m from end B. Determine the shear force at a section from the left-hand end of the beam X = 3.0 m. Input your answer as a value only in kN to one decimal place and without +/- sign. w kN/m M kNm B X -1.5 m- A- -1.5 m -1.5 m-