The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w= 53 kN/m over 1.5 m from the left-hand end and moment loading M - 53 kNm at 1.5 m from end B. Determine the shear force at a section from the left-hand end of the beam X = 3.0 m. Input your answer as a value only in kN to one decimal place and without +/- sign. w kN/m M kNm EB X -1.5 m- A- -1.5 m -1.5 m-

The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w= 53 kN/m over 1.5 m from the left-hand end and moment loading M - 53 kNm at 1.5 m from end B. Determine the shear force at a section from the left-hand end of the beam X = 3.0 m. Input your answer as a value only in kN to one decimal place and without +/- sign. w kN/m M kNm EB X -1.5 m- A- -1.5 m -1.5 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2 (Bending Moment and Shear Force)The simply supported beam AD is subject to a uniform load over the segment BCtogether with a concentrated force applied at C as shown in figure 1.0 below.a. Plot the shear and moment diagrams of the beam.b. If the beam has a cross-sectional area as shown in figure 2.0 below,determine the bending stress at location F
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
The simply supported beam shown below carries its own weight, a uniformly distributed live load of 300 lbs/ft, and a concentrated dead load På at midspan. The cross-section of the beam is U- shaped. It has two rows of reinforcing bars at the bottom. The bottom row has five #6 bars and the top row has three #6 bars. Let ƒ' =4,000 psi and ƒ¸ = 60 ksi. The cross-sectional area of a #6 bar is 0.44 in.². W₁ = 300 lbs/ft 10 ft. PD * 10 ft. 17 in. 3 in. b 8 #6 bars + 00 6 in. 00 14 in. b + 9 in. State the difference between a tension-controlled beam and a compression-controlled beam in terms of the strain in the reinforcement in precise and succinct sentences. Why does ACI require that a beam has to be tension-controlled?
The box beam in the figure is made of four pieces of wood nailed to each other as shown.Since the distance between the nails is 32 and the allowable cutting force on each nail is 160, (a=16, b=38, c=32, d=190, F=160) a) Maximum allowable vertical shear force in the beam? b) Determine the corresponding maximum shear stress in the beam.
d=450 mm
A 240mm diameter circular simply supported beam carries a concentrated load, uniformly distributed load and a triangular load as shown in the figure. Using Area Moment Method, Solve the following unknowns. Let P = 195KN, a = 2m, and the modulus of elasticity of beam is 100GPA. NOTE: WRONG SIGN IS WRONG. WRONG UNITS IS WRONG. w w B Im If the shear at a point 1m from the roller support is equal to -182.66666666667KN, determine the value of "w". kN/m Determine the deflection at point 2n from the hinge support. (Note: Put a negative sign if the deflection is going down) III
Please show all steps.
Consider the beam shown in (Figure 1). Take P = 2 kip and w = 1.9 kip/ft. Point E is just to the right of the 2-kip load. Follow the sign convention. Figure -6 ft D -6 ft W B 4 ft E 4 ft 1 of 1 > C Determine the normal force at point D. Express your answer in kilopounds to three significant figures. ND = Submit Part B V|| ΑΣΦ ↓↑ vec 5 VD= Request Answer Determine the shear force at point D. Express your answer in kilopounds to three significant figures. ——| ΑΣΦ ↓↑ vec ? ? kip kip
Are load combinations an example of superposition? True False The response due to loads A and B together = The Load Combinations The following table contains the results of several analyses for the reaction at the base of a frame. All forces are in kips. Component Horizontal Vertical Dead 0.66 2.50 Live 0.99 3.75 Earthquake 3.00 2.58 Compute all the relevant load combinations for dead, live, and earthquake. Then answer the following questions. Give all answers in absolute value (no negative signs).
E F (600)mm EA EA P= 180 kN EA A B 0-e diagram of the bars 300 тm 300 тm 300 тm The rigid beam given in the figure is supported by three identical bars. Cross-sectional area of the bars are A=(4 ) cm? and they are made of ideal elastic-perfectly plastic material. If a force P= calculate the residual stresses in each bar. (ơ=240 MPa and E=210 000 MPa) : (180 ) kN is applied to the beam and removed,
Problem Solving. 1. The maximum bending moment for a 4 meters freely supported beam has been found to be 15 kN-m. If the allowable bending stress is 9 MPa, design the beam with respect to bending. Use E = 12,000 MPa a. a. Investigate if the computed dimensions will not exceed the allowable shearing stress of 0.90 MPa. b. Investigate if the computed dimensions will not exceed the allowable deflection of L/360. w (kN/m) 4m
Help please!