A dentist using a dental drill brings it from rest to maximum operating speed of 339,000 rpm in 2.0 s. Assume that the drill accelerates at a constant rate during this time. (a) What is the angular acceleration of the drill in rev/s? |rev/s² (b) Find the number of revolutions the drill bit makes during the 2.0 s time interval. rev Additional Materials Reading

A dentist using a dental drill brings it from rest to maximum operating speed of 339,000 rpm in 2.0 s. Assume that the drill accelerates at a constant rate during this time. (a) What is the angular acceleration of the drill in rev/s? |rev/s² (b) Find the number of revolutions the drill bit makes during the 2.0 s time interval. rev Additional Materials Reading

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

grindstone increases in angular speed uniformly from 4.10 rad/s to 19.0 rad/s in 4.10 s. (a) Calculate the grindstone's angular acceleration. rad/s2 (b) Through what angle does it turn during that time? rad
Using the equations attached solve the following: 1.What is the average angular velocity between t = 2.0 s and t=3.1 s ? Express your answer using two significant figures. 2.What is the average angular acceleration between t = 2.0 s and t =3.1 s ? Express your answer using two significant figures.
hw 26 question 5 part a
hw 27 question 4
A runner increases her speed from 3.1 ms to 3.5ms during the last 15 seconds of her run What was her acceleration during her big push to the finish?
A wheel is spinning at 440 rev/s. It undergoes an angular acceleration until it reaches an angular velocity of 527 rev/s. While accelerating, it completed 2414 revolutions. Determine how long the wheel was accelerating and its angular acceleration during that time. Ata .- s rev/s2
A 40-N weight hangs from a (massless inelastic) cord that runs around the outside of a pulley. The pulley is a uniform solid disk of radius 12.8 cm and mass 6.5 kg. You may assume the system is released from rest. Determine the angular acceleration of the pulley. Express your answer in rad/s², to at least one digit after the decimal point. 40 N
A rotating wheel requires 3.08-s to rotate through 37.0 revolutions. Its angular speed at the end of the 3.08-s interval is 98.3 rad/s. What is the constant angular acceleration of the wheel? rad/s2
Macmillan Learning Your computer has an optical disk drive that can spin up to 10,000 rpm (which is about 1045 rad/s). If a certain disk is spun at 352.9 rad/s during the time it is being read, and then comes to rest over 0.569 seconds, what is the magnitude of the average angular acceleration of the disk? average angular acceleration: If the disk is 0.12 m in diameter, what is the magnitude of the linear acceleration of a point 1/3 of the way out from the center of the disk? linear acceleration: x10 rad/s² TOOLS m/s²
Help
A phonograph record accelerates from rest to 36.0 rpm in 4.53 s. (a) What is its angular acceleration in rad/s²? rad/s² (b) How many revolutions does it go through in the process? rev
A weight is tied to a rope that is wrapped around a pulley. The pulley is initially rotating counterclockwise and is pulling the weight up. The tension in the rope creates a torque on the pulley that opposes this rotation. a) On the axes below, draw a graph of the angular velocity versus time for the period from the initial instant shown until the weight comes back down to the same height. Take the initial angular velocity as positive. b) Draw a graph of the angular acceleration versus time for the same time period.