A dc generator has no load output voltage of 120V. Its armature circuit resistance is 0.95 ohm and its field coils are separately energized. If the load is rated 2000 watts at 115V, what power could be delivered to the load?

A dc generator has no load output voltage of 120V. Its armature circuit resistance is 0.95 ohm and its field coils are separately energized. If the load is rated 2000 watts at 115V, what power could be delivered to the load?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter31: Three-phase Alternators

Section: Chapter Questions

Problem 1RQ: What conditions must be met before two alternators can be paralleled together?

See similar textbooks

Related questions

Q: A 4-pole DC generator has 1,000 turns on its rotor. It is being turned by a prime mover at 4,000 RPM…

Q: A 6-pole lap wound generator has 900 conductors. The e.mf induced per one tur being 3 V. the…

A: Given lap connected , So, No. of poles = No. of parallel paths = 6 Given voltage per turn = 3 volts…

Q: If it is desired to bring alternating current out of a generator, what kind of a "take-off" system…

A: If the alternating current is required from the generator a copper or brass rings are connected at…

Q: A 6 pole DC lap wound generator has 41 armature conductors with flux per pole is 23 mWb and the…

Q: A 250 V d.c. shunt generator has 1250 watts constant loss. Find out load current at maximum…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 12 V generator has an internal resistance of 0.05 ohm. Two loads are connected in parallel to its terminals, one drawing a 12 A current and the other dissipating energy at the rate of 200 W. What is the terminal voltage of the generator with this load? Ans. 0.82 volts
A 220V series generator has an armature resistance of 0.04Ω. If the generated emf is 230V and the drop across the series field winding is 9V, what is the ohmic resistance (in ohms) of the series field winding?
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
There are 72 slots in a 3-phase, 8-pole, 50 Hz, star connected alternator. There are 2 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 150° electrical and the flux per pole is 0.05 Weber sinusoidally distributed. Calculate the emf induced per phase.
A 6 pole DC lap wound generator has 41 armature conductors with flux per pole is 23 mWb and the e.m.f generated is 80 V, then the speed of the machine is O 0.74 rps O 84.84 rps O 7.43 rps 84.84 rps
A 200V/100V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be the same, the applied voltage should be ?
2.
A four-pole, wave-wound generator has 220 coils of 10 turns each. The resistance of each turn is 0.02 Ω. Find the resistance of the armature winding.
Please solve , last time i got wrong answer
10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A. What will be the temperature of the winding when current has fallen to 3.91 A applied voltage being constant. Assume temperature coefficient at 15'C is equal to 1/254.5 per °C
Determine the peak-to-peak ripple and dc output voltages in Figure 2. The transformer has a 48 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. (you may neglect Rsurge). 120 V rms 00000 ellee Figure 2 Rug www 10 100 F ww R₁ 3.3k
Calculate the voltage per phase for a 1500 rpm, 4 pole alternator having a double layer winding with 16 turns per coil. The slots per pole phase are 8 and the coil span is 20 slots. The phase spread is 60o and the flux per pole is 25.8 milli webers.