A cylindrical tank, 1.20-m diameter and 2.50m high weighs 2850 N. The tank float in water with a draft of 1.40m. Use unit weight of lead = 110KN/m³ 8. How much lead in kN is required if it is attached at the outside bottom of the tank. a. 12.6 b. 15.3 C. 13.9 d. 59.9

A cylindrical tank, 1.20-m diameter and 2.50m high weighs 2850 N. The tank float in water with a draft of 1.40m. Use unit weight of lead = 110KN/m³ 8. How much lead in kN is required if it is attached at the outside bottom of the tank. a. 12.6 b. 15.3 C. 13.9 d. 59.9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A 25-mm diameter shaft with density 7,870 kg/m³ is pulled through a cylindrical bore as shown. Oil with a kinematic viscosity of 8.2 104 m²/s and SG-0.89 fills the 0.3-mm gap between the shaft and the bore. Find the magnitude of the force P required to pull the rod through the bore with a constant speed of 2.5 m/s. 0.5 m 15°
y=25kN/m P1=24kN P2=7kN
STRUCTURAL ANALYSIS II
Determine the member force LK(kN) in the figure shown. "十2m十十 2 m 2 m 2 m 2 m 2 m- 2m 2 50 kN 50 kN 50 kN 50 kN M. 50 kN 50 kN 50 EN it 4 m V3 3 PLLLE B. D. 25 m-25 m - 3 m -3m 25 m4-2.5 m
se that 1 of 1 Consider the frame shown in (Figure 1). Suppose that F₁ = 850 N Figure 200 N/m Y Part C FA= Y Part B Submit 60° Determine the magnitude of the reaction at pin A Express your answer to three significant figures and include the appropriate units. Submit PA Value Request Answer A μÁ FB = Value Request Answer Fo= Value Determine the magnitude of the reaction at pin B. Express your answer to three significant figures and include the appropriate units. 2m Units Submit Request Answer Units - 0 < 1 of 1 Determine the magnitude of the reaction at pin C on CB Express your answer to three significant figures and include the appropriate units. Units ? ? 2m ?
Find the value of R1 and R2, x = 2m
Moments of Inertia. Determine Ix and kx.
Beam determine the support reactions (solve using integral)
1. Compute the R1 value in newton for the beam 2. Compute the R2 value in newton for the beam 3. Compute the midspan value of Ely for the beam in two decimal places and in terms of kN-m³
Problem 4: Inputs: ● ● B C Weight of person = 165 lb μ = 0.4 0 = 60° W A System 1 B C W a) Max weight that can be lifted in system 1 b) Max weight that can be lifted in system 2 System 2 Close-up view of pulley system In each scenario, you must determine the maximum weight, w, that can be lifted before the man slips. The problem starts out as a pulley problem, but thereafter it is a friction problem. (Thought you were done with that right?)
Gate AB in figure below is a homogenous mass of 180 kg, 1.2 meter wide into the paper, resting on smooth bottom B. For what water depth hin meters will the force at point B be zero? Use specific weight of glycerin to be 12360 N/m³ and water to be 9790 N/m3. Water Glycerin h 2 m A 1 m 60° О а. 3.56 оБ. 1.82 О с. 1.12 O d. 2.52
Determine the Reaction at A for the beam shown. Answer must be written up to 3 decimal places. Include the unit of measurement