A cylindrical piece of steel 80 mm dia and 120 mm long is subjected to an axial compressive force of 50,000 kg. Calculate the change in the volume of the piece if bulk modulus = 1.7 x 106 kg/cm2 and Poisons' ratio = 0.3.

A cylindrical piece of steel 80 mm dia and 120 mm long is subjected to an axial compressive force of 50,000 kg. Calculate the change in the volume of the piece if bulk modulus = 1.7 x 106 kg/cm2 and Poisons' ratio = 0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. Determine the lateral strain. * Your answer Determine the axial strain. Your answer Determine the Poisson's ratio v. * Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 40 mm, an inside diameter of 30 mm, and a shear modulus of G1 = 42 GPa. The solid steel core has a diameter of 30 mm and a shear modulus of G2 = 84 GPa. Assume L = 380 mm. The composite shaft is subjected to a torque of T= 820 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end Brelative to end A. T T (1) B Answers: (a) T1 = MPa T2 = MPa (b) PBIA rad (2)
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
A cylindrical bar of steel 9.9 mm (0.3898 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Determine the force that will produce an elastic reduction of 3.0×10-3 mm (1.181 ×10-4 in.) in the diameter. For steel, values for the elastic modulus (E) and Poisson's ratio (v) are, respectively, 207 GPa and 0.30. i N
The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an outside diameter of 60 mm and a wall thickness of 5 mm, a solid 40 mm diameter aluminum [E= 70 GPa rod (2), and a solid 30 mm diameter aluminum rod (3). The member lengths are L1 2 000 mm, L2 = 1 200 mm, and L3 %D 3D800 mm. The following loads act on the assembly: P = 150 kN, Q = 80 kN, and R = 115 kN. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A.
A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to tension. Determine the magnitude of the load required to produce a 10-4 in. change in diameter if the deformation is entirely elastic. Assume a Young’s modulus of 11 * 106 psi and a Poisson’s ratio of 0.33.
If length of rod is 2 m and a radius of 20 mm is made of high-strength steel. The rod is subjected to a torque T, which produces a shear stress below the proportional limit. If the cross section at one end is rotated 45 degrees in relation to the other end, and the shear modulus G of the material is 90 GPa, calculate the amount of applied torque?
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
The figure shown an elasto-plastic material with tensile strain hardening stress-strain relation. The modulus of elasticity is 25000000 psi, yield strength is 70 ksi, and the slope of the strain-hardening portion of the stress-strain diagram is 3000000 psi. A. Calculate the elastic and the plastic strain when unloading occurs at 90 ksi B. Calculate the stress value and state whether it is tension or compression at zero Strain? Strain
A tapered steel bar of length 2m is subjected to an axial load of 20kN. Take modulus of steel as 200GPa. What is the strain produced in the bar? (in 10-5) = 100 mm 2m >= 50 mm 20000 N