A cylindrical insulation for a steam pipe has an inside radius of 5 cm, an outer radius of 10 cm, and a thermal conductivity of 0.5 W/(m K). The inside surface of the insulation is at a temperature of 200 oC, and the outside surface is at 20 oC. Determine the heat loss per meter length of the insulation. O a. 185 W/m O b. 518 W/m O c. 581 W/m O d. 815 W/m

A cylindrical insulation for a steam pipe has an inside radius of 5 cm, an outer radius of 10 cm, and a thermal conductivity of 0.5 W/(m K). The inside surface of the insulation is at a temperature of 200 oC, and the outside surface is at 20 oC. Determine the heat loss per meter length of the insulation. O a. 185 W/m O b. 518 W/m O c. 581 W/m O d. 815 W/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A pipe is covered with three insulation layers where the corresponding thicknesses are 150 mm, 250mm and 300mm and the respective thermal conductivities are 3.2 W/m°C, 2.1 W/m°C and 1.5 W/m C. The length of the pipe is 3m. The inner side of the pipe which has a diameter of 300 mm is exposed to a hot gas at 1000 °C with convection coefficient of 50 W/m2°C and the temperature of the inner side of the pipe surface is 800 °C. The air outside the pipe is at 25°C with a convection coefficient of 35 W/m2°C. a. Draw a schematic diagram which shows the heat transfer process b. Calculate the Heat transfer rate c. The overall heat transfer coefficient "U" of the system based on the inner pipe d. Temperature at each of the layers and at the outermost surface of the pipe.
GChoose the right answer 1. The temperature profile for steady hest conduction through a plane wall of constant thermal conductivity is a. logarithmic b. parabolic 2. A brick wall (k-0.75 W/mK ) transmits $02 of heat loss through another wall (k-0.25 W/mK, x-100 mm). If the temperature difference across both walls is the same, the thickness of the brick wall would be a.150 mm c. linear 6T b. 240 mm c. 300 mm d. 375 mm 3. The maximum temperature at the center of the solid sphere of radius R having heat generation q (W/m') is given by g'R +9R b. T, + 4k T+9R 6k d. T+9R 8k a. 2k C. 4. The internal thermal resistance of a solid can be ignored if the Biot number is less than a. 1 b. 0.5 c. 0.1 d. Fourier number 5. The ratio of heat transfer of a fin to the heat transfer without fin is referred to as a. fin resistance b. fin efficieney efin effectiveness d. fin conductance.
A 1,155 ft², 4 in. thick concrete wall has inside and outside surface temperatures of 24°C and 4°C. A 2 in. insulation batt with a thermal conductivity of k= 0.03 Btu/(h. ft. °F) is added to the wall. Determine the reduction in heat transfer rate. What is the thickness of the insulation in meters? 0.0508 x Your response differs from the correct answer by more than 10%. Double check your calculations. m What is the thermal conductivity value of the insulation batt in W/(m. K)? 0.05188 W/(mK) What is the R-value of the concrete wall (in m². K/W)? 0.022578 X Your response differs from the correct answer by more than 10%. Double check your calculations. m². K/W What is the R-value of the insulation batt (in m² K/W)? 1.9584 X Your response differs from the correct answer by more than 100%. m² K/W What is the heat transfer rate (in W) when the insulation is added? X W What is the percent reduction in the heat transfer rate? 96 x %
A 1-in Sch 40 stainless steel pipe with a thermal conductivity of 45 W/m-K can move 1,000 kg of saturated steam per hour at 150 °C. Refractory material 0.25 inches thick with a thermal conductivity of 0.025 W/m-K insulates the pipe. At a temperature of 25 °C, the pipe is exposed to the outside air. There is a 1135 W/m2 internal heat transfer coefficient.40 W/m2-K is the outside heat transfer coefficient, whereas -K. Suppose that only the radial direction is involved in steady-state heat transfer and that radiation effects are negligible. ✓ Determine how much heat is being lost through these pipes to the environment.a. 399.1 W/mb. 1525.0 W/mc. 618.4 W/md. 1128.7 W/me. none of the above √ How about the insulated pipe's surface temperature?a. 118.5 °Cb. None of the abovec. 101.5 °Cd. 216.3 °Ce. 292.2 °C
Heat is produced in a long resistance wire q.u= 1.5 W/cm3. The radius of the wire is given as r1=0.3 cm and the thermal conductivity coefficient as ksteel=18 W/m.K. In addition, the wire is covered with a 0.4 cm thick plastic layer with a thermal conductivity coefficient of kplastic = 1.8 W/m.K. The outer surface of the plastic layer loses heat with an average heat transfer coefficient of h=14/W/m2K and by convection to the ambient air at T∞ =250 C. Considering the interface temperature as T1 and accepting the heat transfer as one-dimensional;
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 800 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.
An uninsulated steam pipe passes through a room in which the air and walls are at 25°C. The outside diameter of the pipe is 88 mm, and its surface temperature and emissivity are 200°C and 0.80 respectively. If the coefficient associated with free convection heat transfer from the surface to the air is 15W/m2-k, what is the rate of heat loss for a 5 meter pipe? Round your answer to 2 decimal places.