A cylinder with a 150 mm diameter and 300mm length is put under a compressive load of 665 kips. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data : Tensile load P=40 KN Change in length ∆L=0.0202 mm Initial length L=200 mm Diameter of…

Q: A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips.…

A: D = 6 inL = 12 in P = 150 kipsE  = 8000 ksi v = 0.35

Q: ven the stress-strain data from a tension test, how do you find the following : a) The modulus of…

A: Solution on below attachments

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 860 mm.…

A:

Q: Q1) A specimen with the given dimension is loaded as given in the figure below. Determine; a) The…

A: As per the guidelines of Bartleby we are supposed to only answer the first three subparts of the…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 780 mm.…

A: Allowable tension bending stress = 16 MPa  Allowable compression bending stress = 10 MPa

Q: At an axial load of 25 kN, a 45-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.9 mm while…

A: Axial load (P) = 25 KN = 25 × 103 N Elongation in bar (∆L) = 2.9 mm Change in width (∆b) = 0.19 mm…

Q: In a particular material, if the modulus o rigidity is equal to the bulk modulus, th Poisson Ratio…

A:

Q: A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN.…

A:

Q: A rubber ball is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240…

A:

Q: A hot-rolled steel bar has a diameter of 12 mm was subjected to a tension test as shown in the…

A: NOTE  As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: An elasto-plastic material with strain hardening behavior has a stress-strain relationship composed…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: A stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN.…

A: Given data  Initial diameter of the rod(Di) = 16 mm   Then  Area (Ai) = (π/4)*Di2 = 201.062 mm2…

Q: An aluminum tensile test specimen has a diameter, do = 25 mm and a gauge length of Lo = 250 mm. If a…

A: Given : do = 25 mm Lo = 250 mm  Force = 175 kN  Elongation of Gauge length = 1.25 mm  This is a…

Q: Briefly describe a standard test method which can be used to establish properties of Yield stress…

A: Tensile testing gives a wide range of information about a material.

Q: A 1.5 cm diameter rod pull test was carried out. The measurements of the test, whose initial length…

A: The true stress is calculated as: True stress=F/Afinal σ1=16240×4π×12.0282=143…

Q: Problem NO. 2. A student performed a tensile test in one of his samples, an aluminum specimen which…

A:

Q: A sample material with circular cross-section tapers uniformly. Over a gauge length of 200mm, it…

A:

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 900 mm.…

A:

Q: At an axial load of 24 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 3.1 mm while…

A: Given, Axial load, P = 24 kN or 24000 N Cross section size = 50mm x 20mm Length = 210 mm

Q: 1. A vertical pressure of 70 MPa is applied to an aluminum cube sample with a length of 10 cm on…

A:

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 700 mm.…

A:

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: cylinder with a 6.0 in. diameter and 12.0 in. long is put under a compressive load of 150,000 lbs.…

A: Using formula

Q: calculate the lateral strain and the change in diameter.

A:

Q: Copy the sketch of the tensile stress-strain test (Figure A1) results for a waisted metallic…

A: Objective: To indicate the given points on the stress-strain diagram and calculate the Young's…

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data,  Yield load =161 KN  Maximum load = 242 KN  Length of specimen at fracture = 249 mm…

Q: 3. A new material is being developed and tested in the lab. The column was made using the new…

A: To find the elastic modulus and vicose coefficient

Q: DURING THE STRESS-STRAIN TEST, THE UNIT DEFORMATION AT A STRESS OF 30 MPa WAS OBSERVED TO BE 117 x…

A:

Q: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b.

A:

Q: Length, width and thickness of a plate are 400 mm, 400 mm and 30 mm, respectively. For the material…

A:

Q: In a simple tensile test using a cylindrical test specimen (Dia.=10mm), the applied force was 120 kN…

A: Given data in question  Diameter of sample Force applied  Extension  Standard accepted modulus of…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm.…

A: Given:- The length of beam=760 mmb1=34 mmd1=106 mmb2=20 mmd2=20 mma=7 mmAllowable tensile bending…

Q: At an axial load of 24 kN, a 40-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.7 mm while…

A:

Q: O (MPa) 80 60 40 20 0.002 0.004 0.006 0.008 0.01 0.012 Figure 3 i) Determine the value of yield…

A: Dear student as per bartleby guidelines we are supposed to answer only first 3 sub parts. Kindly…

Q: wo samples of a metal with an elastic modulus of 130 GPa, diameter 10 mm, and gauge length 100 mm…

A: Two samples of a metal are there with the elastic modulus 130GPa.The diameter of the metal is 10 mm…