A cylinder of mass 100 kg is in contact with the smooth surfaces at And B and in static equilibrium when a 300 N force is applied as shown. (a) Determine the reactions at the contact points A and B. (b) Determine the reactions for the pin at C (point) (c) What should be the applied force such that the cylinder loses contact with point A and is about to roll over point B? (Note: the reaction at B will change too) (2 points) 250 mm B 4 1100 mm 300 N

A cylinder of mass 100 kg is in contact with the smooth surfaces at And B and in static equilibrium when a 300 N force is applied as shown. (a) Determine the reactions at the contact points A and B. (b) Determine the reactions for the pin at C (point) (c) What should be the applied force such that the cylinder loses contact with point A and is about to roll over point B? (Note: the reaction at B will change too) (2 points) 250 mm B 4 1100 mm 300 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

CE control rod passes through horizontal hole on the body of the sear system shown in the figure. Knowing that link BD is 250 mm long, determine the force Q required to hold the system in equilibrium when β=20 °.
Determine whether the block shown is in equilibrium, and find the magnitude and direction of the friction force when P= 150 N.
For what value M of the clockwise couple will the horizontal component A, of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? Answers: M = Mr Ax= i 3.25 I 120 lb 3.2 B 1.8' 58 lb-ft lb 1.8' C
4.) The uniform 4-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is attached to the midpoint G of the rod as shown in the figure. The rod leans against a frictionless vertical wall at B. Determine the reactions at A and B and the tension in cord CG. [Answer: T = 20.8 N, Ax= -14.7 N (down), Ay= 29.4 N, Az 11.0 N, B= 29.0 N, where the positive answer indicate the reaction goes in the positive direction of the respective axis and vice versa] Hints: Note the given mass from which you need to calculate weight. IF G is is the midpoint of the rod, then the x, y, z coordinates of that point can be taken to be half the x,y,z components of the position vector FAB 150 mm, B 400 mm 0 150 mm 600 m G
The mass center G of the 1390-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. -1393 mm- 913 mm Answers: Normal force under each of the front tires: Nf = i Normal force under each of the rear tires: N, = i
The uniform (18 kg) bar OA is held in the position Shown by the pin at o" and the cable AB. Detemine the tension T in the cable and the magnitude of the reactions at pin o". 1.5 m 60° 1.2 m
1) Determine the horizontal force P needed to hold the handle in the position shown. Express your answer to three significant figures and include the appropriate units. 2) Determine the x component of reaction at the ball-and-socket joint A. Express your answer to three significant figures and include the appropriate units. 3) Determine the y y -component of reaction at the ball-and-socket joint A. Express your answer to three significant figures and include the appropriate units. 4) Determine the z component of reaction at the ball-and-socket joint A. Express your answer to three significant figures and include the appropriate units. 5) Determine the x component of reaction at the smooth bearing B. Express your answer to three significant figures and include the appropriate units. 6) Determine the z component of reaction at the smooth bearing B Express your answer to three significant figures and include the appropriate units.
2. A vertical force of 80 pounds acts on the crankshaft. Determine the horizontal equilibrium force P that must be applied to the handle, and the x, y, z components of reaction at the journal bearing (A) and thrust bearing (B). The bearing are properly aligned and only exert force reactions on the shaft. 80 lb 8 in. 4 in. 6 in. 14 in. B 10 in. 14 in.
2. Determine the horizontal and vertical components of reaction which the pins exert on member AB of the frame. In other words, find the reactions at pins A and B. 300 lb 60° B 4 ft E -3 ft -3 ft 500 lb
A man weighing 73 N stands at the middle rung of a steel ladder uniformly weighing 43 kN/m. Assuming that the floor and wall are perfectly smooth and that slipping is prevented by cable CD, determine the following: A Tension in the cable B. Reaction at A and B
Problem Statement Based on Problem 5-87 from the textbook. Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is tramsitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components of reaciotn at the journal bearing C and thrust bearing D. The bearings are in proper alignment and exrt only force reactions on the shaft. 300 mm 250 mm 200 mm 80 mm D 150 mm F3 F1=70N F2=85N F3=50N Theta=38 degrees
The 40-kg uniform triangular plate is supported by two small hinges A and B and the cable system shown. For the horizontal position of the plate, determine all hinge reactions and the tension T in the cable. Hinge A can resist axial thrust, but hinge B cannot. See Table D/3 in Appendix D for the mass-center location of a triangular plate. Answers: Ax= Ay- A₂ 0.43 m 0.20 m By B₂= 0.20 m 0.43 m T= 0.91 m. Z Z N N z z N N N N 1.30 m