A custom pipe connection was installed to deliver water to the highest level of a commercial building. During peak hours the discharge through the 150-mm pipe is 100 liters per second, and the demand through the 75-mm pipe is 40 liters per second. The mass of the custom tee fitting is 8 kg, and its hollow volume is 0.025 m³. The pressures at section A and C are 80 kPa and 50 kPa, respectively. Neglect losses. 50 kPa 75 mm dia 100 mm dia 40 Ips 30 tee 400 mm 1 80 kPa 150 mm dia from lower 100 Ips building level 1. 2. 3. the tee fixed. Determine the discharge at section B. Determine the pressure at section B. Determine the magnitude and direction of the force required to keep

A custom pipe connection was installed to deliver water to the highest level of a commercial building. During peak hours the discharge through the 150-mm pipe is 100 liters per second, and the demand through the 75-mm pipe is 40 liters per second. The mass of the custom tee fitting is 8 kg, and its hollow volume is 0.025 m³. The pressures at section A and C are 80 kPa and 50 kPa, respectively. Neglect losses. 50 kPa 75 mm dia 100 mm dia 40 Ips 30 tee 400 mm 1 80 kPa 150 mm dia from lower 100 Ips building level 1. 2. 3. the tee fixed. Determine the discharge at section B. Determine the pressure at section B. Determine the magnitude and direction of the force required to keep

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing through an orifice meter at a rate of 0.096 m² /sec. The diameter of the pipe is 250 mm. Calculate the pressure drop (in Pa) through the orifice meter if the diameter of the throat is 150 mm. Discharge coefficient of orifice meter is 0.62. Density of water is 1000 kg/m³.
The water passing through the turbine of a hydroelectric power plant at a flow rate of 30 m3 /s is poured into the river bed with a velocity of V2=2 m/s. Head loss in turbine and pressure pipe is hk=20 m. Assuming the flow is turbulent and the kinetic energy correction factor α=1.06, find the power supplied by the turbine in MW.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Determine the power required for the pump if the water flow rate is 60 kg/s. The fittings from pipe Di to pipe D2 and from pipe D2 to pipe D3 can be considered to be standard 90° elbows with velocity in pipe 2 for the friction loss. Data: h = 10 m, h2 = 3 m, L1 water viscosity = 1 cP = 103 kg/m-s, p= 1000 kg/m³. The pipe roughness is 0.05 mm. The pump efficiency is 75%. 50 m, L2 = 300 m, L3 = 2 m, D¡ = 0.2 m, D2= 0.5 m, D3 = 0.03 m, (1) D,, L, D2, L, Globe valve D3, L,
4. Two reservoirs, A and B, are connected by a pipeline which is 1300 m long. The surface of reservoir B is 10 m lower than that of reservoir A. There is a small hill between the two reservoirs with the highest point at 500 m along the pipe from A. If the pipeline has a diameter of 300 mm and a friction factor of λ = 0.008 then determine the following: (Ignore the minor losses and assume that the pipe is already flowing full and at a steady flow) (a) The flow in the pipe (b) If the lowest permissible absolute pressure head in the pipeline is 2.5 m of water, determine how high above reservoir A surface level the pipe can be laid so that the minimum pressure condition is satisfied. (Assume atmospheric pressure of 105 Pa.)
2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m3. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s)
What is the minimum power required from the pump to deliver the oil from Reservoir A to Reservoir B as shown in Figure 2 at a rate of 0.30m³/s? The pump has a 70% efficiency rating. V Reservoir A -Oil v= 10-5 m²/s p=950kg/m³ Elevation 135m Steel Pipe, ks =0.046mm, L= 200m, D=250mm Elevation 120m r/D=0.1 Pump Figure 2 r/d=1 Reservoir B abrupt Globe valve, wide open Air at 200kPa Elevation 110m Elevation 100m
Q3
Q.9) If the faucet (gate valve), at E is fully opened and the pump produces a pressure of 350 kPa at A, determine the flowrate out from the faucet at E. The valve at B remain closed. The pipe has an inner diameter of 30 mm, and f=0.01. Include the minor losses of the tee (K=0.4), the two elbows (K=0.9), and the gate valve (K=0.19). 0.65 m 3 m B 5 m
I ll rate
Water at 15°C is transported from a large open tank to the bottom of another open tank above. The surfaces of the two tanks are kept at 160 ft apart vertically. The pipes used have an ID of 3.5 inches, and a total length of the pipe used is 150 ft. In the system, there are two fully open gate valves, 6 90° elbows, and 2 standard tees. The pump used has a mechanical efficiency of 60%, and the volumetric flow rate of water is at 35 (ft^3)/s. Frictional losses due to sudden contraction and expansion are negligible. Determine the Reynolds number of the flow
Question 1 A pipeline of length 2000 m and diameter 200 mm connects two water supply reservoirs together. (a) If the value of the frictional factor, f, for the pipeline is 0.02 then determine the flow in the pipeline when the head difference between the two reservoirs is 20 m. (b) If an increase in demand requires that the flow be increased by 40% then determine what length of the same diameter pipe is required to satisfy this demand if it is connected as shown in Figure 1. Assume that the friction factor for the new pipe is the same as the existing one. New pipeline 20 m