A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its inside diameter = 400 mm The sheet metal thickness = 20 mm. If the blank diameter = 500 mm, determine the reduction. 0,250 0,333 0,500 1811500 0,020 LODO

Q: Impact velocity equation

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: Description of the operation and process of a Bread Manufacturing Plant

A: Operation and process of a bread manufacturing plant consists of several steps like mixing,…

Q: how do you solidify and cool in a metal casting process manufacturing

A:

Q: Thank you

A: given : t = 6.07mm = 0.00607 m F = 38.9 KN = 38900 N τ = 54.4 MPa = 54.4 x 106 N/m2

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: 1)b. The process can only work with thermoplastics and not with thermosets due to the thermal…

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: For the casting of the part whose perspective pictures are given below, take into account the…

A: COVE DESIGN

Q: Which of the following is NOT TRUE with respect to the Elastic Transverse Shear Formula?…

A:

Q: Material Balance Analysis A cannery receives on a given day: 12 tons of raw produce, 5 tons of cans,…

A: Write the waste materials. Cans=53%=0.15 tonsCartons=0.53%=0.015 tonsMisc. material=0.375%=0.225…

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: Course: Computer Aided Manufacturing How to assign codes to any five parts with different…

A: In parts classification and coding, similarities among parts are identified, and these similarities…

Q: discuss the process of creating a good finish when using metals as a raw material in making a…

A: we are to discuss what are methods of generating a better finish with metals

Q: Kind of "manual control and automatic" scrap machine

A: Shaping and Planning are the operation of removing a layer of work material from the flat surface…

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: Mold is manufactured in two parts top and bottom, size has to be smaller than the actual size of the…

A: As per given question  Mold is manufactured in two parts top and bottom, size has to be smaller than…

Q: During the operation of the product, does the part move relative to all other parts already…

A: "Design for Manufacture and Assembly(DFMA)"  optimises the manufacturing and assembly operations of…

Q: Does the following pass the "test" of novelty? A design for a chair that folds.     Passes test…

A: A chair that folds is a common design that has been implemented in numerous products already.…

Q: a)Prepreg formation results in   Tape consisting of randomly oriented fibers Sheet consisting of…

A: Since you have posted multiple independent Multiple choice questions. We will solve the first…

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A:

Q: During machining of aluminum work piece, the cutting process was achieved in begin with dry…

A:

Q: Determine the natural frequency of the system by a) the Equivalent Mass and Equivalent Stiffness…

A: (a) Write the expression of kinetic energy conservation to write equivalent mass of the system.…

Q: In the context of our teaching, which one of the below statements is mostly correct about in…

A: Component design, sometimes known as atomic design (though we prefer "Component design" at…

Q: 1. Find the forces acting on each member: (Round off your answers to 2 decimal places)

A:

Q: Which machine would you recommend given the following information and interest rate is 10%? New Used…

A: Given data as per the question  Interest rate = 10% Calculations considering 1st machineInital cost…

Q: describe the most ideal process of making a toolbox when making at a mass production

A: A toolbox is a box which is used to carry the tools (like plier hammer and many more other types of…

Q: What is the best to stop procrastinating?

A: Introduction-Procrastination is a snare that a considerable lot of us fall into. As a matter of…

Q: Distinguish between the Surface Loads and the Distributed Loads?

A: Load is defined as an external force or a couple to which a member is subjected during its…

Q: give a steps by steps explanation of the solution

A:

Q: The first element in a feature control frame in Solidworks denotes what?

A: The products may vary slightly in terms of dimensions as compared to the initial designs because of…

Q: Engineering Drawing: Dimensions

A:

Q: 1- Metals is more - --than ceramic in this property. 2- The engineering design deals with ----and 3-…

A: Dear Student, As per the Bartleby answering guidelines we are supposed to answer first 3 questions.…

Q: Where does a nonconservative force occur, so that mechanical energy is not conser OA

A: Here non conservative force occurs at point "C" that is point of contact of wheel and ground. Non…

Q: Identify all elements in a feature control frame and what they denote

A: A feature control frame is the description of the conditions and tolerance of any geometric control…

Q: Question 3 10 points V Sav The basic principle to select a material for a product is to use a…

A: The basic principle to select a material for a product is

Q: What 3 types of floor plans that might be encountered in commercial construction?

A: During commercial construction, Architect give design plan depending upon requirements. It provides…

Q: Make a table of the process capabilities of the following advanced machining processes. Use several…

A: Given:To find:

Q: QUESTION 4 Which of the following statements is true about the relative magnitudes of the design…

A: Correct answer: a. The factor of safety is greater than or equal to the design factor.

Q: Questions Three Consider the office chair design below, develop the design matrix and identify its…

A: Given Office chair To find Design matrix Type of chair

Q: 1. Would the part shown in Figure 2 below 'pass inspection'? Yes No _ .062+.004 DRAWING CALLOUT .065…

A: Here, dimension of part is given as 0.062±0.004 which means upper limit is 0.062+0.004=0.066 and…

Q: Give examples fof impact.

A: The definition of impact is one thing crashing into or having an effect on another.

Q: Describe the ideal chip type

A: There are three types  of chips formed in metal cutting using single point cutting tool. They are,…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.