A cube made of an alloy with dimensions of 50mm×50mm×50mm is placed into a pressure chamber and subjected to a pressure of 80 MPa. If the modulus of elasticity of the alloy is 200 GPa and Poisson’s ratio is 0.30, what will be the length of each side of the cube, assuming that the material remains within the elastic region?

Q: A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the…

A: Diameter of rod, d = 0.5 in Change in diameter, ∆d = -10-4 in Young’s modulus, E = 11x106 psi…

Q: Q1) A specimen with the given dimension is loaded as given in the figure below. Determine; a) The…

A: As per the guidelines of Bartleby we are supposed to only answer the first three subparts of the…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 780 mm.…

A: Allowable tension bending stress = 16 MPa  Allowable compression bending stress = 10 MPa

Q: Which of the following is the best representation of the samples' (A and B) axial strains when…

A:

Q: A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN.…

A:

Q: A fluid continuously deforms when exposed to a shear stress.

A: Answer :  True explanation is given in next step

Q: The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor…

A:

Q: An aluminum tensile test specimen has a diameter, do = 25 mm and a gauge length of Lo = 250 mm. If a…

A: Given : do = 25 mm Lo = 250 mm  Force = 175 kN  Elongation of Gauge length = 1.25 mm  This is a…

Q: tion by the cross-sectional area. Is this approach t? To answer this question consider the loading

A: STress is the ratio of force to the cross -sectional area.

Q: A concrete-like material that is cast into a bar is fully restrained at each end against axial…

A:

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural…

A:

Q: A hollow steel shaft of external diameter 100 mm and internal diameter 50 mm is to be replaced by a…

A: Given- External diameter Do=100 mmInternal diameter Di=50 mmSame ploar modulusDiameter of the solid…

Q: 1. An elastoplastic material with strain hardening has the stress strain relationship shown below.…

A:

Q: The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length…

A:

Q: 1Pa. Determine the largest moment M that can be applied as shown to the

A: Calculation of largest BM###

Q: A hollow steel shaft of external diameter 100 mm and internal diameter 50 mm is to be replaced by a…

A: Answer  We are given  External diameter of hollow steel shaft Do=100 mm Internal diameter of hollow…

Q: A rigid horizontal bar (Weight = 20 kips) is supported by two (2) square aluminum columns as shown.…

A:

Q: A cylindrical polymer with a diameter of 10nm when stress is applied to it and a change in diameter…

A: Let the applied Force be F in Newton and A is the area of polymer.Area of…

Q: A sample material with circular cross-section tapers uniformly. Over a gauge length of 200mm, it…

A:

Q: In shown figure the aluminum is subjected to a thermal stress where T1 is 21.957 deg. C and T2 is…

A:

Q: A spherical steel pressure vessel (diameter500 mm, thickness 10 mm) is coated with brittle…

A: Step 1: Stress= E.Ɛ P = 2.05 x 10^5 x 150 X 10-6= 30 GPa Hoop stress = pd/2t = 30x0.5/2 x0.01 =750…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 900 mm.…

A:

Q: 1. A vertical pressure of 70 MPa is applied to an aluminum cube sample with a length of 10 cm on…

A:

Q: An extruded polymer beam is subjected to a bending moment M.  The length of the beam is L = 660 mm.…

A:

Q: A steel bar is 10mm diameter and 4m long. If the temperature drops by 12°C and a = 11.7 um/m°C. what…

A:

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 700 mm.…

A:

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: have more strain, a 10ft bar being stretched 3 inches or a 3ft bar being stretched 3 inches? It…

A: Stretching a material causes it to experience strain, which is determined by the material's original…

Q: Find the stress in each material 600 mm 400 mm 300 mm Bronze Aluminum Steel 120 kN 50 kN A mm 2400…

A:

Q: In shown figure the aluminum is subjected to a thermal stress where T₁ is 21.957 deg. C and T2 is…

A:

Q: - A Compound bar composed of three bar as shown .Determine the stress if the temperature change from…

A:

Q: show solution of: A liquid compressed in a container has a volume of 1 liter at a pressure of 1 MPa…

A:

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm.…

A: Given:- The length of beam=760 mmb1=34 mmd1=106 mmb2=20 mmd2=20 mma=7 mmAllowable tensile bending…

Q: A 2 m long alloy bar of 1500 mm? cross-section area hangs vertically and has a collar securely fixed…

A:

Q: b) Figure Q1 shows ceramic specimens subjected to the pure uniaxial force. Specimen A is compressed…

A: An elemental area can be subjected to stress due to applied load . For uniaxial it is subjected to…

Q: 90 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000…

A: Given data stress= 200 MPa rupture lifetime be 509 h

Q: A 10-mm-diameter Brinell hardness indenter produced an indentation 1.55 mm in diameter in a steel…

A:

Q: a.) Plot the S-N curve for this alloy. b.) Does this material have an endurance limit? Explain. c.)…

A: As per company policy, we are supposed to answer only the first three subparts. Kindly repost to get…