Need help please, use 3 sig figs for answers A crate is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zyplane. Point A is located at a height of h = 111.76 cm above the top of the crate directly over thegeometric center of the top surface. Use the given dimensions from the table below to perform thefollowing calculations:a.) Determine the position vector TAD that describes rope AD.b.) Compute the unit vector to that points from point C to point A.c.) If rope AB carries a tension force of magnitude P= 776 N, determine the force vector F thatexpresses how this force acts on point A.Express each vector in Cartesian components to three significant figures.2013 Michael SwanbomBY NC SAсba. FAD =b. cA= (Fr= (Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Besure to align your cartesian unit vectors with the coordinate axes shown in the figure.VariableabValue76.2 cm78.74 cm33.87 cmi +B+ak) cmk)e) N

A crate is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zy plane. Point A is located at a height of h = 111.76 cm above the top of the crate directly over the geometric center of the top surface. Use the given dimensions from the table below to perform the following calculations: a.) Determine the position vector AD that describes rope AD. b.) Compute the unit vector üc that points from point C to point A. Fr that c.) If rope AB carries a tension force of magnitude F = 776 N, determine the force vector expresses how this force acts on point A. Express each vector in Cartesian components to three significant figures. 2013 Michael Swanbom CC 30 BY NC Variable Value C. Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Be sure to align your cartesian unit vectors with the coordinate axes shown in the figure. a b b с a. FAD = b.ûCA = 76.2 cm 78.74 cm 33.87 cm i y i+ a k) cm e) N

A crate is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zy plane. Point A is located at a height of h = 111.76 cm above the top of the crate directly over the geometric center of the top surface. Use the given dimensions from the table below to perform the following calculations: a.) Determine the position vector AD that describes rope AD. b.) Compute the unit vector üc that points from point C to point A. Fr that c.) If rope AB carries a tension force of magnitude F = 776 N, determine the force vector expresses how this force acts on point A. Express each vector in Cartesian components to three significant figures. 2013 Michael Swanbom CC 30 BY NC Variable Value C. Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Be sure to align your cartesian unit vectors with the coordinate axes shown in the figure. a b b с a. FAD = b.ûCA = 76.2 cm 78.74 cm 33.87 cm i y i+ a k) cm e) N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.
F, = 50 N F2 = = 40 N -5 45° F1 = 20 N
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
Draw Front and Side and top with all dimensions please
Please answer the questions below.
a diagonal of a polygon is a line segment that connects nonadjacent vertices of the polygon.in the following polygons, a triangle has 3 sides and 0 diagonal, a quadrilateral has 4 sides and 2 diagonals, a pentagon has 5 sides and 5 diagonals, a hexagon has 6 sides and 9 diagonals. predicts the number of diagonals in a 12-sided polygon.
Jensen Figure 6-71 Sketch 3 orthographic projections (i.e. top, front, right). Draw them on 10x10 cross section graph paper. - On each of the projections, label the inclined surface shown with its appropriate letter. - Identify if it is showing in first-angle projection or third-angle projection. b) a) K K Fig. 6-71 Sketching assignment 16.
Below is problem MV1 from the course pack. In an earlier assignment, you created a multiview drawing of this part. Model this part with SolidWorks, with each grid spacing equal to one inch. Create a SolidWorks drawing of this part, with Front, Top, and Right Views. Import dimensions from the SolidWorks part file, and place them on the drawing so that they can be easily read. Add a note that all dimensions are inches. Add your personalized title block that you created in Chapter 2 to this drawing. *Important: Save the drawing first as SolidWorks Drawing (filetype *.slddrw) and then as an eDrawing (filetype *.edrw)! You will upload the eDrawing in Blackboard, not the SolidWorks Drawing - the SolidWorks drawing is associated with the part file, I cannot open the sw drawing unless you also send the part file; however, l can open the eDrawing without the part file.
Need help .Please
Please help show me how drawing will look in isometric drawing.