A corner column is reinforced with 12 - 20mm dia. RSB with fy = 415 MPa. Concrete Strength f'c = 28 MPa. Neglect the concrete area occupied by longitudinal reinforcement A. Locate the plastic centroid measured from x-axis and y-axis B. Resultant factored moment due to a factored axial load Pu = 3000 kN applied at 300 mm normal to y-axis and 180mm normal to x-axis. 50 mm 50 mm 150 mm 200 mm 150 mm 50 mm 100 mm 350 mm 50 mm 250mm

A corner column is reinforced with 12 - 20mm dia. RSB with fy = 415 MPa. Concrete Strength f'c = 28 MPa. Neglect the concrete area occupied by longitudinal reinforcement A. Locate the plastic centroid measured from x-axis and y-axis B. Resultant factored moment due to a factored axial load Pu = 3000 kN applied at 300 mm normal to y-axis and 180mm normal to x-axis. 50 mm 50 mm 150 mm 200 mm 150 mm 50 mm 100 mm 350 mm 50 mm 250mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
Determine the additional longitudinal reinforcements (mm2) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).
A half-block concrete masonry unit is subjected to compression until failure.The outside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 38 mm. The loadis applied perpendicular to the hollow cross section and the maximum loadis 296 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
Given Data: Concrete dimensions Area of steel 625 560 f = 30 MPa ЗHD25 f, = 420 MPa A, = 2457 mm² 65 %3D b = 250 Required: What is the maximum uniformly distributed live load it can support in addition to dead load?
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
just answer d to f
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
please answer in the nearest 3 decimal numbers
3 نقاط The minimum reinforcement using mild steel in slab should not be less than .., if fy=420 MPa ...... 2.0% 1.8% 0.15% 0.18%
Correct solution
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.