A cord is wrapped around the rim of a wheel 0.225 m in radius, and a steady pull of 41.5 N is exerted on the cord. The wheel is mounted on frictionless bearings on a horizontal shaft through its center. The moment of inertia of the wheel about this shaft is 5.50 kg · m?.

A cord is wrapped around the rim of a wheel 0.225 m in radius, and a steady pull of 41.5 N is exerted on the cord. The wheel is mounted on frictionless bearings on a horizontal shaft through its center. The moment of inertia of the wheel about this shaft is 5.50 kg · m?.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

An old grindstone, used for sharpening tools, is a solid cylindrical wheel that can rotate about its central axle with negligible friction. The radius of the wheel is 0.330 m. A constant tangential force of 200 N applied to its edge causes the wheel to have an angular acceleration of 0.804 rad/s2. (a) What is the moment of inertia of the wheel (in kg · m2)? kg · m2 = (b) What is the mass (in kg) of the wheel? kg= (c) The wheel starts from rest and the tangential force remains constant over a time period of 4.50 s. What is the angular speed (in rad/s) of the wheel at the end of this time period? rad/s=
Calculate the rotational inertia of a meter stick, with mass 0.67 kg, about an axis perpendicular to the stick and located at the 39 cm mark. (Treat the stick as a thin rod.) X kg · m2
To develop muscle tone, a woman lifts a 3.70 kg mass held in her hand. She uses her biceps muscle to flex the lower arm through an angle of 60.0°. Ignore gravity. (a) What is the angular acceleration if the mass is 24.0 cm from the elbow joint, her forearm having a moment of inertia of 0.250 kg · m2, and the muscle force being 760 N at an effective perpendicular lever arm of 2.50 cm? (b) How much work does she do?
You stand on a frictional platform that is rotating at 1.6 rev/s. Your arms are outstretched, and you hold a heavy weight in each hand. The moment of inertia of you, the extended weights, and the platform is 7.9 kg · m2. When you pull the weights in toward your body, the moment of inertia decreases to 3.7 kg · m2. (a) What is the resulting angular speed of the platform?(b) What is the change in kinetic energy of the system?(c) Where did this increase in energy come from? (Select all that apply.) -your internal energy -gravity -kinetic energy of the platform -mass of the weights -air resistance
A cord is wrapped around the rim of a wheel 0.300 m in radius, and a steady pull of 38.5 NN is exerted on the cord. The wheel is mounted on frictionless bearings on a horizontal shaft through its center. The moment of inertia of the wheel about this shaft is 5.35 kg⋅m2 Compute the angular acceleration of the wheel.
The wheels of a wagon can be approximated as the combination of a thin outer hoop, of radius r = 0.368 m and mass 5.46 kg, and two thin crossed rods of mass 8.23 kg each. A farmer would like to replace his wheels with uniform disks ta = 0.0588 m thick, made out of a material with a density of 8290 kg per cubic meter. If the new wheel is to have the same moment of inertia about its center as the old wheel about its center, what should the radius of the disk be? 0.267 %3D Enter numeric value
The wheels of a wagon can be approximated as the combination of a thin outer hoop, of radius r = 0.368 m and mass 5.27 kg, and two thin crossed rods of mass 7.37 kg each. A farmer would like to replace his wheels with uniform disks ta = 0.0462 m thick, made out of a material with a density of 8290 kg per cubic meter. If the new wheel is to have the same moment of inertia about its center as the old wheel about its center, what should the radius of the disk be?
A wheel of radius 0.35 m rotates in a clockwise sense about a fixed axle with negligible friction at an initial angular speed of 2.6 rad/s. The wheel's mass of 17 kg is concentrated in its rim. You apply a clockwise torque to the rotating wheel by pushing on the rim tangentially with a constant force of 22 N. Find the wheels angular speed, in radians per second, 0.085 seconds after you start pushing on the rim.
A uniform spherical shell of mass M = 6.0 kg and radius R = 18.0 cm rotates about a vertical axis on frictionless bearings (see the figure). A massless cord passes around the equator of the shell, over a pulley of rotational inertia I = 3.60×10-3 kg m2 and radius r = 6.0 cm, and its attached to a small object of mass m = 4.0 kg. There is no friction on the pulley's axle; the cord does not slip on the pulley. What is the speed of the object after it has fallen a distance h = 1.1 m from rest: Use work - energy considerations
A circular disk with a radius of 0.38 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. The mass of the disc is 0.73 kg. The moment of inertia of a disc is I =1/2MR^2 F1 = 2.3 N applied at the outer edge of the disc. F2 = 3.6 N applied at a distance of 0.29 from the center of the disc. What is the angular acceleration of the disc?
An object's moment of inertia is 2.50 kgxm^2 . Its angular velocity is increasing at the rate of 3.30 rad/s^2 . What is the net torque on the object?
A 17.0-m length of hose is wound around a reel, which is initially at rest. The moment of inertia of the reel is 0.490 kg-m², and its radius is 0.150 m. When turning, friction at the axle exerts a torque of magnitude 3.20 N-m on the reel. If the hose is pulled so that the tension in it remains a constant 26.0 N, how long does it take to completely unwind the hose from the reel? Neglect the mass and the thickness of the hose, and assume that the hose unwinds without slipping.