A copper wire is stretched with a stress of 90 MPa (10,000 psi) at 30°C (68°F). If the length is held constant, to what temperature must the wire be heated to reduce the stress to 45 MPa (5000 psi)? Ecu = 110 GPa; a = 17 (10-6)/ °C %3D

A copper wire is stretched with a stress of 90 MPa (10,000 psi) at 30°C (68°F). If the length is held constant, to what temperature must the wire be heated to reduce the stress to 45 MPa (5000 psi)? Ecu = 110 GPa; a = 17 (10-6)/ °C %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: P2. Design a cylindrical thin-wall composite fuselage for storing compressed natural gas at a…

Q: Two initially straight bars are joint together and attached to support as shown in Figure 4. Let us…

A: We have to determine a ) If the supports are unyielding , find the normal stress in each bar . ( b )…

Q: A 200 x 100 x 50 mm steel block is subjected to a hydrostatic pressure of 15 MPa. The Young's…

A: As per given V=200×100×50mm3 Hydrostatic pressure =15mpa Poisson ratio =0.3 We have to find…

Q: A thin plate of linear elastic materials (E v = 0.25) is in plane stress (o, = Txz = Tyz = 0). The…

A: Given that, Modulus of elasticity of the material, E=200 GPa,Kinematic viscosity of the material,…

Q: circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; V = 0.33] pipe has an outside diameter of…

A: Given:Youngs modulus, E=70 GPaThermal coefficient, α=22.5*10-6/°CV=0.33Outside diameter, D=225…

Q: A closed cylinder (26 + 60) cm long, containing 3 MPa pressurized fluid, due to this pressure a…

A: Since we provide answers up to three subparts only, we will answer the first three subparts here.…

Q: Q2\ Find the necessary change in temperature in the copper bar so that the rigid bar remains…

A: For the rigid bar to remain horizontal, the moment due to the UDL should be equal to the moment due…

Q: * Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when…

A: Given data as per the question The initial temperature of the bar = 200 c The final temperature of…

Q: A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the…

A: Given: Length, L=3m Thermal diffusivity, k=0.4 Initial temperature, f(x)=100-10x Boundary…

Q: Steel railroad reels 10 m long are laid with a clearance of 3 mm at a temperature of 15°C. At what…

A: Given in question:Clearance, C=3 mmTemperature, T=15o CLength of rail, L=10 mE=200 GPaα=11.7 μm/m oC

Q: Steel railroad reels 12 m long are laid with a clearance of 2.5 mm at a temperature of 20°C. At what…

Q: Coefficient of Thermal Expansion Steel Rod (figure) a. Change in length if the rod is heated to…

Q: Current Attempt in Progress A solid 72-mm-diameter cold-rolled brass [G-38.5 GPa) shaft that is 1.21…

A: Given: The diameter of the brass shaft is db=72 mm=72mm×1m1000 mm=0.072 m. The outer diameter of…

Q: ds were at the same level before the block was attached. etermine the stress in each rod after the…

A: To Find : The stress in each rod . Given : The temperature is T=100°F The properties of rod are :…

Q: Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N…

Q: The bar will induce

A: No stress (A)

Q: unusable, If we consider the material 2 ánd will it take to lift up material Z? Also, what will be…

A: Given: Tst,o=150°Cx=4 mm=0.004 mTi= 25°C∆ts=2 mink=0.15 W/mKρcp=1.5×106 J/m3KTo determine:Time taken…

Q: When installed, bar AB had negligible axial stress. When the bar's temperature is 124°F the axial…

A: Given : A bar AB had negligible stress axial stress when installed . When bar temperature is…

Q: A steel tube is restrained between two rigid walls 80 cm apart, At a temperature of 28 degree…

Q: 3. Three bars each made from different materials are placed between walls when the temperature is…

Q: As shown in Fig, there is a gap between the aluminum bar and the rigid slab that is supported by two…

A: Given data as per question Area of copper rod =500 mm2 Area of aluminium rod =400 mm2 we know that…

Q: A solid body of length L with a rectangle cross section has a temperature distribution equals to : T…

Q: A solid aluminum [E = 70 GPa; a = 22.5 × 10-6/°C]rod (1) is connected to a solid bronze [E = 100…

A: E1 = 70 GPa = 70 X 103 N/mm2 a1 = 22.5 x 10-6 /C E2 = 100 GPa = 100 x 103 N/mm2 a2 =16.9 x 10-6 /C…

Q: Consider a steel bar attached at both ends. Assume that at 20 °C this bar is free of tension.…

A: Thermal stresses generated due to a temperature increase fromT1 to T2 is given byσ=E∝ T2-T1where…

Q: Problem 2. A block of cast iron was wrapped in the thin aluminum foil as shown on the figure. At…

A: Solution: Given Data: *The initial stress in the foil, σi=0 *The temperature of the Nitrogen is,…

Q: 1.1 (A). A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of…

Q: Figure 1 shows a system of three bars each made of different materials, and connected together and…

Q: A solid 0.12 in. diameter steel (E = 30,000 ksi: a = 6.5 × 10-6/°F] wire is stretched between fixed…

Q: The two cylindrical rod segments shown in the figure below (Figure 1) are fixed to the rigid walls…

A: Find the new length of aluminum segment

Q: 3. A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls 5…

Q: A steel is 10 mm diameter and 2 m long. It is stretched with force of 20 kN and extends by 0.2 mm…

Q: An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] bar is subjected to a tensile load P. The…

A: We will calculate the longitudinal and transverse strain due to both temperature change ans load P…

Q: 2. A wire is stretched between 2 rigid posts separated by a distance L. If the surrounding…

Q: A copper [E = 102 GPa, a = 17.1x10-6/°C] rod (2) is placed within a steel [E = 204 GPa, a =…

Question

A copper wire is stretched with a stress of 90 MPa (10,000 psi) at
30°C (68°F). If the length is held constant, to what temperature must
the wire be heated to reduce the stress to 45 MPa (5000 psi)? Ecu =
%3D
110 GPa; a = 17 (10 )/ °C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

"ll zain 1Q ۲۸ مارس، ۲۰۲۱ -> docs.google.com/forms/d/e Q3/ A compound bar is held between two supports as shown in figure 2. If the temperature of the bar is raised from 25°C to 75°C, find the stresses induced in each rod by assuming (a) if the supports do not yield and (b) if the supports yield by 0.25 mm. Take E1= 200 kN/mm2, E2 = 30 kN/mm2, E3 = 100 kN/mm2, And, a1= 1.2 x 10-5/°C, a2= 1.8 x 10-5/°C d3= 1.6 x 10-5/°C Q3/ * 0= 150 mm 0= 100 mm 0= 50 mm Figure 2 200 mm 300 mm 500 mm (1) 01= 194.78 N/mm2, a2= 48.7 N/mm2, 03= 21.64 N/mm2/(2) 01= 133.14 N/mm2, 02 33.28 N/mm2, a3= 14.79 N/mm2 (1) 01- 184 3anm2, 92- 44.73 N/mm2. 03- 24.64 N/min2/ (2) a1 143.14 N/mm2 o2 36 21 N/mm2, 03-14.79 N/mm2 (1) a1- 190.28 N/mm2, 02 48.26 N/mm2,
Just want to understand this review example
Mechanical engineering. A steel beam is installed in a building when the ambient temperature is -12C. If the beam if fixed at it's ends (prevented from expanding/contracting), calculate the stress that will develop in the beam if the ambient temperature rises to +32C. State whether the stress is tension or compression. Assume E 200,000 MPa and \alpha L = 12x10-6 (/\deg C)
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
I need the answer as soon as possible
answer as soon as possible
A 5-m rod having a uniform cross-sectional area of 1000 sq. mm. is secured between two walls5 meters apart. The load on the rod is zero at 27 °C. E = 200 GPa, α = 11.25x10-6 m/m-°C. Whenthe temperature rises to 57°C: What is the stress in the rod assuming that the walls are rigid and stress (in the rod) if the walls spring together with a total distance of 0.5 mm? pls box final answer
answer and show solution
This question was answered for me but the second answer is not clear how he/she got 0.55 and 0.45 for the rods.