A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in the plane YY. Determine the maximum permissible bending moment which can be applied to the beam (a) for bottom flange in tension, and (b) for bottom flange in compression, if the safe stresses for the material in tension and compression are 30 MN/m2 and 150 MN/m' respectively. A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in the plane YY. Determine the maximum permissible bending moment which can be applied to the beam (a) for bottom flange in tension, and ( b) for bottom flange in compression, if the safe stresses for the material in tension and compression are 30 MN/m2 and 150 MN/m' respectively. Can I get the solution for A and B.. Thanks! Subject: Strengh of Materials

Q: Draw the missing Shear force(V) and Moment (M) diagram for the loading given

A:

Q: please write clean and as much detail as you can 2. please draw the FBD

A: Given:-

Q: Q.2: The simply supported beam in Fig .below has a rectangular cross section mm wide and 200 mm…

A: Given data is

Q: A vertical loads of 400 N acts at the end of a horizontal rectangular cantilever beam 2 m long and…

A:

Q: 1. Find the resultant force in a brass beam from a normal stress of 98 MN/m2 with a square…

A: Answer 1: σ=98 MN/m2s=12 mm Need to determine the resultant force in a brass beam.

Q: A simply supported beam with a cross-section as shown in Fig. 1.19 spans 15 m and carries a total…

A:

Q: A cantilever 10 m long caries two concentrated loads, one at the free end and the other at the…

A:

Q: (a) Compute the reactions at the supports. (b) Derive the bending moment expressions for segments…

A:

Q: Q2: The cantilever beam shown in Fig.2. is uniformly tapered along its length in both x and y…

A: Given data  a load = 100 kN at its free end.  corner boom cross-sectional area =  900 mm² central…

Q: 2. Calculate the maximum shear and maximum moment for the following load diagram. (show all your…

A:

Q: 2. For the 20 meter beam shown, there is a roller at "A" (Ay = 52 kN; it is acting upward), and a…

A: For the 20 meter beam shown, there is a roller at "A" (Ay= 52 KN; it is acting upward), and a pin…

Q: 3.35B. For the section illustrated, find the second moment of area, the location of the neutral…

A:

Q: 1. Three vertical wires each 4.5m long hang in the same vertical plane from a horizontal ceiling and…

A:

Q: 19. AT-section of a beam, as shown in Fig. 5.44,is subjected to a vertical shear force of 100 kN.…

A: you dont give fig but i assumed this fig

Q: A rectangular beam of 100 mm wide is subjected to maximum shear force of 50 kN, the corresponding…

A: Given data , w= 100 mm. τmax=3 N/mm2  Vmax= 50 KN= 50000 N  Let b= depth

Q: When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise…

A: A beam with Uniformly distributed load given

Q: For a steel circular cantilever beam, 10mm in diameter, 700mm in length with an applied load of…

A: M= (3/4 My + 1/3 Mp)My = 24543.5 N.mmMp = 41666.66667 N.mmYield strength= 250 MPad = 10 mmy = d/2F =…

Q: A simply supported beam carries a distributed load of 10 kN/m over a span of 5 m and a concentrated…

A: Given Data: udl intensity w=10 KN/m Span L=5 m Point loads =10 KN ,8 KN

Q: 4. Plot the shear and moment diagrams. 1000 lb ↓ F8+12 -12 ft- (Undergrad students)

A: Here in this problem, a beam with given load is provided.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.